To Replace Headlight Bulb, Interlocks and Relays

SERVICE AND ADJUSTMENTS

If “jumper cables” are used for emergency starting, use the following procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

WEAK OR	FULLY CHARGED
DEAD BATTERY	BATTERY

FIG. 23

REPLACING BATTERY (See Figs. 24 and 25)

WARNING: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding.

•Lift seat pan to raised position.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with bolt and nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) ter- minal with remaining bolt and nut. Tighten securely.

•Lower seat pan.

SEAT PAN

02602

Fig. 24

TERMINAL		NUT	BOLT
COVER			BOLT
COVER
POSITIVE			NEGATIVE
(RED)			NEGATIVE
(RED)			(BLACK)
CABLE			(BLACK)
CABLE			CABLE
	02603		CABLE

FIG. 25

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 26)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

02495

Fig. 26

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is nec- essary, see engine manual.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment.

433401 specifications

The Poulan 433401 is a remarkable chainsaw that embodies a blend of power, efficiency, and user-friendly design. Ideal for both professionals and DIY enthusiasts, this model is thoughtfully engineered to handle a variety of cutting tasks, from felling trees to pruning shrubs.

One of the most notable features of the Poulan 433401 is its powerful engine. Equipped with a 33cc two-stroke engine, it delivers ample power while maintaining a lightweight build, which is critical for maneuverability during extended usage. The engine's design allows for efficient fuel consumption, enabling users to maximize their cutting time without frequent refueling. This is particularly useful for those who take on larger jobs or require extended operational periods.

The chainsaw boasts a 16-inch guide bar, making it suitable for a range of cutting applications. The length strikes a balance between efficient cutting and ease of control, making it perfect for both seasoned users and those new to chainsaw operation. The Oregon chain enhances cutting performance, providing smooth and reliable operation while ensuring a clean cut.

One of the standout technologies incorporated into the Poulan 433401 is its automatic oiling system. This essential feature ensures that the chain remains adequately lubricated during operation, reducing friction and wear. The automatic system not only enhances the lifespan of the chain and bar but also ensures optimal performance, allowing users to focus on the task at hand rather than constant maintenance.

Safety features are paramount in the design of the Poulan 433401. It includes a chain brake designed to stop the chain in an event of kickback, which is a common risk when using chainsaws. Additionally, the front and rear handles are ergonomically designed, providing a comfortable grip and reducing user fatigue. This attention to ergonomics helps improve precision and control, particularly during prolonged use.

The Poulan 433401 is also relatively easy to start, thanks to its spring-assisted starter mechanism and purge bulb feature. This makes it accessible to users of all skill levels, eliminating the frustrations often associated with starting smaller engine chainsaws.

Overall, the Poulan 433401 combines power, versatility, and safety. Its innovative design and user-centric features make it a reliable tool for various cutting tasks, setting it apart as a favorable choice in the chainsaw market. Whether for forestry professionals or homeowners looking to maintain their landscapes, the Poulan 433401 stands out as a valuable asset.

Poulan 433401 manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Models: 433401