Check Tire Pressure

ASSEMBLY / PRE-OPERATION

INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 8 and 9)

1.Install remote cable bracket to discharge chute with 5/16-18 carriage bolt and 5/16-18 locknut as shown. Tighten securely.

2.Install remote cable eyelet to chute deflector with 1/4-20 shoulder bolt and 1/4-20 locknut as shown. Tighten nut securely. Cable eyelet will be loose on shoulder bolt.

3.Install spring hooks between hex nuts on chute rotater head and into hole in chute deflector as shown.

	1/4-20	SPRING
	1/4-20	CHUTE
	SHOULDER	CHUTE
	SHOULDER	DEFLECTOR
	BOLT	DEFLECTOR
	BOLT
		HOOK
		BETWEEN
		HEX NUTS
		ON CHUTE
	1/4-20	ROTATER
	LOCKNUT	HEAD
		5/16-18
		CARRIAGE
		BOLT
	CABLE
	EYELET
	REMOTE
	CABLE
	BRACKET
	5/16-18
	LOCKNUT

Fig. 8

CHUTE DEFLECTOR

CONTROL LEVER

Fig. 9

The tires on your snow thrower were overinflated at the fac- tory for shipping purposes. Correct and equal tire pressure is important for best snow throwing performance.

•Reduce tire pressure to 14-17 PSI.

Page 7

Image 7

Poulan 96198003602, 437921 owner manual Install Chute Deflector Remote Control See Figs, Check Tire Pressure

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in Carton Install Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See Figs Check Tire Pressure Install Chute Deflector Remote Control See Figs Ignition KEY OperationKnow Your Snow Thrower Primer Recoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety Requirements To USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To USE Fuel SHUT-OFF Valve See Fig To Throw Snow See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See Fig If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before Stopping Lubrication MaintenanceGeneral Recommendations Before Each USE Engine Cleaning Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute Deflector To Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig Carburetor Engine OIL StorageOther Fuel System Troubleshooting Auger 27 LH Auger HousingKEY Part Description Scraper BAR Exploded Impeller Pulley Gearbox Assembly178675X431 Corner Bracket Clean OUT Tool Bearing Skid Plate RH Auger BearingBearing Plug Skid Plate LH Shield Retainer Strap Knob BlackPOP Rivet Chute Snow Shield Rotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat Shield Loop Handle RH Loop Handle LH427513X431 Pivot Support Weldment Handle Knob SpacerRetainer Knob RED Traction ROD Impeller ROD Flood Headlight Wire HarnessConsole Panel Headlight Bezel 01.03.005-B Exploded END Plate Speed Selector AssemblyDrive Plate Assembly Wheel HUB Engine Mounting Plate Complete LCT EngineFrame 427963X428 Idler Pulley Impeller BeltTraction Belt Idler ARM Bracket 432335X421 Wheel Assembly LH432336X421 422663 Safety Ignition KEY DECAL, Danger 181037 Service Notes Limited Warranty

Poulan 96198003602, 437921 Install Chute Deflector Remote Control See Figs, Check Tire Pressure

Models: 96198003602 437921

ASSEMBLY / PRE-OPERATION

INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 8 and 9)

CHECK TIRE PRESSURE