STORAGE

Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Remove safety ignition key; store it in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ex- haust area is still warm.

19

Page 18 Page 20
Page 19
Image 19
Poulan 96192004600, 438361, PR8P27ES owner manual Storage, Other, Fuel System, Engine OIL, Cylinder
Page 18 Page 20

PR8P27ES, 96192004600, 438361 specifications

The Poulan 438361, 96192004600, and PR8P27ES are notable offerings from Poulan Pro, a brand known for its innovation in outdoor power equipment. These tools are designed to cater to a variety of landscaping and maintenance tasks, making them essential for both residential users and professionals.

The Poulan 438361 is particularly recognized for its efficient performance. It features a robust 38cc two-stroke engine that delivers ample power for tasks such as trimming, edging, and light brush clearing. The combination of lightweight design and an ergonomic handle allows users to operate the equipment with minimal fatigue, even during extended periods. The advanced air filtration system helps prolong engine life by reducing the risk of clogging, ensuring that peak performance is maintained over time.

The 96192004600 offers a unique attachment system that enhances its versatility significantly. This multi-tool design allows users to customize their equipment by exchanging attachments for different tasks, such as pruning, blowing leaves, or tilling. This adaptability not only saves users from needing multiple machines but also provides a streamlined experience for homeowners and professionals alike. With easy-to-follow instructions and quick-change couplings, switching between attachments requires minimal effort.

The PR8P27ES model emphasizes user convenience with its push-start technology. This electric start feature eliminates the hassle of traditional pull-start mechanisms, offering an easier experience, especially for those less experienced in handling power tools. Its durable construction ensures long-lasting performance, while the low maintenance requirements mean that users can spend more time focused on their projects rather than on upkeep.

All three models benefit from Poulan Pro's commitment to safety and comfort. Features like anti-vibration technology in the handles and noise-reduction designs provide a more pleasant user experience. Additionally, the incorporation of safety switches and guards ensures that users can operate these machines with confidence.

In conclusion, the Poulan 438361, 96192004600, and PR8P27ES models embody a range of technologies and features that position them as top choices for outdoor power equipment. With their powerful engines, versatile attachment capabilities, and user-centric designs, these tools meet a variety of landscaping needs while ensuring reliability and ease of use. Whether for professional landscaping or home maintenance, these Poulan Pro models stand out as efficient and effective solutions.
Top Page Image Contents