TROUBLESHOOTING POINTS
PROBLEM | CAUSE | CORRECTION | |||
Excessive | 1. | Worn, bent or loose blade. | 1. | Replace blade. Tighten blade bolt. | |
vibration | 2. | Bent blade mandrel. | 2. | Replace blade mandrel. | |
| 3. | Loose/damaged part(s). | 3. | Tighten loose part(s). Replace damaged parts. | |
|
|
|
|
|
|
Engine continues | 1. | Faulty | 1. | Check wiring, switches and connections. If not |
|
to run when oper- |
| system. |
| corrected, contact an authorized service center/ | |
|
|
| department. | ||
ator leaves seat |
|
|
| ||
|
|
|
|
| |
with attachment |
|
|
|
|
|
clutch engaged |
|
|
|
|
|
|
|
|
|
|
|
Poor cut - uneven | 1. | Worn, bent or loose blade. | 1. | Replace blade. Tighten blade bolt. |
|
| 2. | Mower deck not level. | 2. | Level mower deck. | |
| 3. | Buildup of grass, leaves, and trash under | 3. | Clean underside of mower housing. | |
|
| mower. |
|
|
|
| 4. | Bent blade mandrel. | 4. | Replace blade mandrel. | |
| 5. | Clogged mower deck vent holes from | 5. | Clean around mandrels to open vent holes. | |
|
| buildup of grass, leaves, and trash around |
|
|
|
|
| mandrels. |
|
|
|
Mower blades will | 1. | Obstruction in clutch mechanism. | 1. | Remove obstruction. |
|
not rotate | 2. | Worn/damaged mower drive belt. | 2. | Replace mower drive belt. | |
| 3. | Frozen idler pulley. | 3. | Replace idler pulley. | |
| 4. | Frozen blade mandrel. | 4. | Replace blade mandrel. | |
|
|
|
|
|
|
Poor grass | 1. | Engine speed too slow. | 1. | Place throttle control in “FAST” position. |
|
discharge | 2. | Travel speed too fast. | 2. | Shift to slower speed. | |
| 3. | Wet grass. | 3. | Allow grass to dry before mowing. | |
| 4. | Mower deck not level. | 4. | Level mower deck. | |
| 5. | Low/uneven tire air pressure. | 5. | Check tires for proper air pressure. | |
| 6. | Worn, bent or loose blade. | 6. | Replace blade. Tighten blade bolt. | |
| 7. | Buildup of grass, leaves and trash under | 7. | Clean underside of mower housing. | |
|
| mower. |
|
|
|
| 8. | Mower drive belt worn. | 8. | Replace mower drive belt. | |
| 9. | Blades improperly installed. | 9. | Reinstall blades sharp edge down. | |
| 10. | Improper blades used. | 10. | Replace with blades listed in parts manual. | |
| 11. | Clogged mower deck vent holes from | 11. | Clean around mandrels to open vent holes. | |
|
| buildup of grass, leaves, and trash around |
|
|
|
|
| mandrels. |
|
|
|
Headlight(s) not | 1. | Switch is “OFF”. | 1. | Turn switch “ON”. |
|
working | 2. | Bulb(s) or lamp(s) burned out. | 2. | Replace bulb(s) or lamp(s). | |
(if so equipped) | 3. | Faulty light switch. | 3. | Check/replace light switch. | |
| 4. | Loose or damaged wiring. | 4. | Check wiring and connections. | |
| 5. | Blown fuse. | 5. | Replace fuse. | |
|
|
|
|
|
|
Battery will not | 1. | Bad battery cell(s). | 1. | Replace battery. |
|
charge | 2. | Poor cable connections. | 2. | Check/clean all connections. | |
| 3. | Faulty regulator (if so equipped). | 3. | Replace regulator. | |
| 4. | Faulty alternator. | 4. | Replace alternator. | |
|
|
|
|
|
|
Engine "back- | 1. | Engine throttle control not set at “SLOW” | 1. | Move throttle control to “SLOW” position and allow |
|
fires” when turn- |
| position for 30 seconds before stopping |
| to idle for 30 seconds before stopping engine. | |
| engine. |
|
|
| |
ing engine “OFF” |
|
|
|
| |
|
|
|
|
| |
|
|
|
|
|
|
Engine dies when | 1. | Reverse operation system (ROS) is not | 1. | Turn ignition key to ROS "ON" position. See |
|
tractor is shifted |
| "ON" while mower or other attachment is |
| Operation section. | |
into reverse |
| engaged. |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
25
