Poulan 530087390 Keep oil cap and fasteners securely tightened, Maintain chain saw with care

S Keep oil cap and fasteners securely tightened.

S Nonconforming replacement compo- nents or the removal of safety devices may cause damage to the unit and pos- sible injury to the operator or bystand- ers. Use only Poulan PRO! accesso- ries and replacement parts as recommended. Never modify your saw.

SMaintain chain saw with care.

SKeep unit sharp and clean for better and

safer performance.

S Follow instructions for lubricating and changing accessories.

S Unplug the chain saw from the power source when not in use, before servic- ing, and when changing accessories and attachments, such as saw chain and guard.

S Check for damaged parts. Before fur- ther use of the chain saw, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its in- tended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its op- eration. A guard or other part that is damaged should be properly repaired or replaced by an authorized service dealer unless otherwise indicated else- where in the instruction manual.

SWhen not in use, chain saws should be stored in a dry, high or locked-up place out of the reach of children.

SWhen storing saw, unplug and use a bar sheath or carrying case.

ELECTRICAL SAFETY

WARNING: Avoid a dangerous environment. To reduce the risk of elec- trical shock, do not use in rain, in damp or wet locations, or around swimming pools, hot tubs, etc. Do not expose to snow, rain, or water to avoid the possibil- ity of electrical shock. Do not handle ex- tension cord or plug with wet hands.

SUse a voltage supply as shown on the

nameplate of the unit.

SAvoid dangerous situations. Do not use

in the presence of flammable liquids or gases to avoid creating a fire or explo- sion and/or causing damage to unit.

S To reduce the risk of electrical shock, this appliance has a polarized plug (one blade is wider than the other) and will re- quire the use of a polarized extension cord. The appliance plug will fit into a po- larized extension cord only one way. If

3

the plug does not fit fully into the exten- sion cord, reverse the plug. If the plug still does not fit, obtain a correct polar- ized extension cord. A polarized exten- sion cord will require the use of a polar- ized wall outlet. This plug will fit into the polarized wall outlet only one way. If plug does not fit fully into the wall outlet, reverse the plug. If the plug still does not fit, contact a qualified electrician to install the proper wall outlet. Do not change the equipment plug, extension cord recep- tacle, or extension cord plug in any way.

S To reduce risk of electrical shock, use extension cords specifically marked as suitable for outdoor appliances. The electrical rating of the cord must not be less than the rating of unit. The cord must be marked with suffix “W--A” (in Canada, “W”). Use a polarized cord. Make sure your extension cord is in good condition. Inspect extension cord before use and replace if damaged. Do not use a damaged cord. Cord insula- tion must be intact with no cracks or de- terioration. Plug connectors must be undamaged. An undersized extension cord will cause a drop in line voltage re- sulting in loss of power and overheating. If in doubt, use the next heavier gauge. The lower the gauge number, the heavi- er the cord (see SELECT AN EXTENSION CORD in the OPERATION section). Do not use multiple cords.

SDo not abuse cord. Never carry the unit by the extension cord or yank extension cord to disconnect unit.

SSecure extension cord to power cord to

prevent disconnection from unit.

SDo not use the unit if the switch does not turn the unit on and off properly, or if the lockout does not work. Repairs to the switch must be made by an authorized

service dealer.

S Keep extension cord clear of operator and obstacles at all times. Position cord so that it will not be caught on branches. Do not expose cords to heat, oil, water, or sharp edges.

STo avoid the possibility of electric shock, avoid body contact with any grounded conductor, such as metal fences or

pipes.

S Ground Fault Circuit Interrupter (GFCI) protection should be provided on circuit or outlet to be used. Receptacles are available having built-in GFCI protection and may be used for this measure of safety. Inspect chain saw cords periodi- cally and if damaged, have repaired by an authorized service dealer.