SIf engine does not stop, move choke lever to FULL CHOKE position.

ON/STOP Switch

Throttle Trigger

HOW TO START YOUR UNIT

WARNING: The trimmer head will turn while starting the engine. Avoid any con- tact with the muffler. A hot muffler can cause serious burns.

STARTING A COLD ENGINE (or a warm engine after running out of fuel)

Starting Position

Starter Handle

Choke

Lever

Primer Bulb

Muffler

1.Set unit on a flat surface.

2.Slowly press the primer bulb 6 times.

3.Move choke lever to FULL CHOKE by aligning lever with position shown on de- cal (see illustration below).

Choke position decal

4.Squeeze the throttle trigger fully and hold through all remaining steps.

5.Pull starter rope handle sharply until en- gine sounds as if it is trying to start, but do not pull rope more than 6 times.

6.As soon as engine sounds as if it is trying to start, move choke lever to HALF CHOKE by aligning lever with position shown on decal (see following illustra- tion).

Choke position decal

7.Pull starter rope sharply until engine runs, but no more than 6 pulls. If the engine doesn’t start after 6 pulls (at the HALF CHOKE position), move the choke lever to the FULL CHOKE position and press the primer bulb 6 times. Squeeze and hold the throttle trigger and pull the starter rope 2 more times. Move the choke lever to the HALF CHOKE position and pull the starter rope until the engine runs, but no more than 6 pulls. If the engine doesn’t start, repeat procedure 2 additional times.

NOTE: If engine still doesn’t start, it is probably flooded. Proceed to STARTING A FLOODED ENGINE.

8.Once the engine starts, allow it to run 10 seconds, then move the choke lever to OFF CHOKE by aligning lever with posi- tion shown on decal (see illustration be- low). Allow the unit to run for 30 more se- conds at OFF CHOKE before releasing the throttle trigger. NOTE: If engine dies with the choke lever in the OFF CHOKE position, move the choke lever to the HALF CHOKE position and pull the rope until engine runs, but no more than 6 pulls.

Choke position decal

STARTING A WARM ENGINE

1.Move the choke lever to the HALF CHOKE position.

2.Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until the engine runs smoothly.

3.Pull starter rope sharply until engine runs, but no more than 5 pulls.

4.Allow engine to run 15 seconds, then move the choke lever to the OFF CHOKE position.

NOTE: If engine has not started, pull start- er rope 5 more pulls. If engine still does not run, it is probably flooded.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the choke lever in the OFF CHOKE position; then, pull the rope to clear the engine of ex- cess fuel. This could require pulling the starter handle many times depending on how badly the unit is flooded.

5

Page 4 Page 6
Page 5
Image 5
Poulan 530163413 instruction manual HOW to Start Your Unit, Starting a Warm Engine, Starting a Flooded Engine
Page 4 Page 6

530163413 specifications

The Poulan 530163413 is a highly regarded replacement part designed specifically for Poulan chainsaws and outdoor power equipment. This particular component is a magneto ignition coil, an essential element that plays a crucial role in the starting and performance of small engines.

One of the standout features of the Poulan 530163413 is its reliability. The ignition coil is engineered to create a spark that ignites the fuel-air mixture in the engine's cylinder. A strong, consistent spark is vital for ensuring the chainsaw operates smoothly and efficiently, allowing users to tackle tough tasks without interruptions. This part is built to meet or exceed OEM specifications, guaranteeing optimal performance and durability.

In terms of technology, the Poulan 530163413 utilizes advanced materials that enhance its longevity and resistance to wear and tear. Given that outdoor power equipment often operates in rugged conditions, the coil is designed to withstand various environmental factors, including heat and vibration. This durability ensures that users can rely on their tools over a prolonged period, reducing the need for frequent replacements.

Another notable characteristic of the ignition coil is its compatibility. The Poulan 530163413 is designed to fit a wide range of Poulan chainsaw models, making it a versatile choice for both professionals and DIY enthusiasts. Users can quickly identify this part as the solution to ignition issues often caused by a faulty ignition coil, thereby restoring functionality and efficiency to their equipment.

Installation is user-friendly, as the Poulan 530163413 generally comes with all necessary mounting hardware, making it accessible for those looking to carry out repairs without professional assistance. This aspect empowers users to maintain and service their chainsaws, which can lead to long-term savings and improved performance.

In summary, the Poulan 530163413 ignition coil is a robust and reliable component that enhances the functionality of Poulan chainsaws. With its high-quality materials, compatibility with various models, and ease of installation, it is an ideal choice for anyone needing to replace a faulty ignition coil. As a critical part of the engine’s ignition system, it ensures that users can enjoy a powerful and efficient chainsaw experience.
Top Page Image Contents