REPLACE SPARK PLUG

Replace the spark plug each year to ensure the engine starts easier and runs better. Set spark plug gap at 0.025 inch. Ignition timing is fixed and nonadjustable.

1.Twist, then pull off spark plug boot.

2.Remove spark plug from cylinder and discard.

3.Replace with Champion RCJ-6Y spark plug and tighten securely with a 3/4 inch socket wrench.

4.Reinstall the spark plug boot.

REPLACING THE LINE

1.Remove spool by firmly pulling on tap button.

2.Clean entire surface of hub and spool.

3.Replace with a pre-wound spool, or cut two lengths of 12-1/2feet of 0.080! (2 mm) di- ameter Poulan PROr brand line.

WARNING: Never use wire, rope, string, etc., which can break off and become a dangerous missile.

4.Insert ends of the lines about 1/2 inch (1 cm) into the small holes on the inside of spool.

Spool

Small

Holes

Line exit holes

 

Line in Notch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Line in Notch

Hub

5.Wind the line evenly and tightly onto the spool. Wind in the direction of the arrows found on the spool.

6.Push the lines into the notches, leaving 3 to 5 inches (7 -- 12 cm) unwound.

7.Insert the lines into the the exit holes in the hub as shown in the illustration.

8.Align the notches with the line exit holes.

9.Push spool into hub until it snaps into place.

10.Pull the lines extending outside of the hub to release the lines from the notches.

REPLACING THE CUTTING HEAD

1.Align hole in the dust cup with the hole in the side of the gearbox by rotating the dust cup.

2.Insert a small screwdriver into aligned holes. This will keep the shaft from turn- ing while removing and installing trimmer head.

Screwdriver

3.While holding the screwdriver in position, remove trimmer head by turning clock- wise.

4.Thread replacement trimmer head onto the shaft by turning counterclockwise. Tighten until secure.

5.Remove the screwdriver.

CARBURETOR ADJUSTMENT

WARNING: Keep others away when making idle speed adjustments. The trimmer head will be spinning during this procedure. Wear your protective equipment and observe all safety precautions.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

S Engine will not idle when the throttle is released.

Make adjustments with the unit supported so the cutting attachment is off the ground and will not make contact with any object. Hold the unit by hand while running and making ad- justments. Keep all parts of your body away from the cutting attachment and muffler.

Idle Speed Adjustment

Allow engine to idle. Adjust speed until engine runs without stalling (idle speed too slow).

S Turn idle speed screw clockwise to increase engine speed if engine stalls or dies.

STurn idle speed screw counterclockwise to decrease engine speed.

Air Filter

Cover

Idle Speed Screw

If you require further assistance or are unsure about performing this procedure, contact an authorized service dealer or call 1--800--554--6723.

8

Page 7 Page 9
Page 8
Image 8
Poulan 530163413 Replace Spark Plug, Replacing the Line, Replacing the Cutting Head, Carburetor Adjustment
Page 7 Page 9

530163413 specifications

The Poulan 530163413 is a highly regarded replacement part designed specifically for Poulan chainsaws and outdoor power equipment. This particular component is a magneto ignition coil, an essential element that plays a crucial role in the starting and performance of small engines.

One of the standout features of the Poulan 530163413 is its reliability. The ignition coil is engineered to create a spark that ignites the fuel-air mixture in the engine's cylinder. A strong, consistent spark is vital for ensuring the chainsaw operates smoothly and efficiently, allowing users to tackle tough tasks without interruptions. This part is built to meet or exceed OEM specifications, guaranteeing optimal performance and durability.

In terms of technology, the Poulan 530163413 utilizes advanced materials that enhance its longevity and resistance to wear and tear. Given that outdoor power equipment often operates in rugged conditions, the coil is designed to withstand various environmental factors, including heat and vibration. This durability ensures that users can rely on their tools over a prolonged period, reducing the need for frequent replacements.

Another notable characteristic of the ignition coil is its compatibility. The Poulan 530163413 is designed to fit a wide range of Poulan chainsaw models, making it a versatile choice for both professionals and DIY enthusiasts. Users can quickly identify this part as the solution to ignition issues often caused by a faulty ignition coil, thereby restoring functionality and efficiency to their equipment.

Installation is user-friendly, as the Poulan 530163413 generally comes with all necessary mounting hardware, making it accessible for those looking to carry out repairs without professional assistance. This aspect empowers users to maintain and service their chainsaws, which can lead to long-term savings and improved performance.

In summary, the Poulan 530163413 ignition coil is a robust and reliable component that enhances the functionality of Poulan chainsaws. With its high-quality materials, compatibility with various models, and ease of installation, it is an ideal choice for anyone needing to replace a faulty ignition coil. As a critical part of the engine’s ignition system, it ensures that users can enjoy a powerful and efficient chainsaw experience.
Top Page Image Contents