WARNING: If the saw is operated with a loose chain, the chain could jump off the guide bar and result in serious injury to the operator and/or damage the chain mak- ing it unusable.

BEFORE STARTING ENGINE

WARNING: Muffler is very hot dur- ing and after use. Do not touch the muffler or allow combustible material such as dry grass or fuel to do so.

WARNING: Be sure to read the fuel handling information in the safety rules sec- tion of this manual before you begin. If you do not understand the fuel handling information do not attempt to fuel your unit. Seek help from someone that does understand the in- formation or call the customer assistance help line at 1-800-554-6723.

FUELING ENGINE

WARNING: Remove fuel cap slow- ly when refueling.

HELPFUL TIP

To obtain the correct oil mix ratio, pour 3.2 ounces of 2-cycle synthetic oil into one gallon of fresh gas.

This engine is certified to operate on un- leaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/WEED EATER brand synthetic oil is recommended. A 40:1 ratio is obtained by mixing 3.2 fluid ounces (95 ml) of oil with 1 gallon (4 liters) of unleaded gasoline. Included with this saw is a 3.2 ounce (95 ml) container of Poulan/ Weed Eater brand synthetic oil. Pour the en- tire contents of this container into 1 gallon (4 liters) of gasoline to achieve the proper fuel mixture. DO NOT USE automotive or marine oil. These oils will cause engine damage. When mixing fuel follow the instructions printed on the container. Always read and follow the safety rules listed under HANDLE FUEL WITH CAUTION.

CAUTION: Never use straight gasoline in your unit. This will cause permanent engine damage and void the limited warranty.

FUEL REQUIREMENTS

This engine requires the use of minimum 87 octane [R+M]/2 clean gasoline.

IMPORTANT

Use of alcohol blended fuels (called gasohol or using ethanol or methanol) can cause major engine performance and durability problems.

WARNING: Alternative fuels (not gasoline) such as E--15 (15% alcohol), E--20 (20% alcohol), E--85 (85% alcohol) are NOT classified as gasoline and are NOT approved for use in 2--stroke gasoline engines. Use of al- ternative fuels will cause problems such as: im- proper clutch engagements, overheating, va-

por lock, power loss, lubrication deficiency, deterioration of fuel lines, gaskets and internal carburetor components, etc. Alternative fuels cause high moisture absorption into the fuel/oil mixture leading to oil and fuel separation.

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lubri- cation. Lubrication is provided by the auto- matic oiler system when the oil tank is kept filled. Lack of oil will quickly ruin the bar and chain. Too little oil will cause overheating shown by smoke coming from the chain and/ or discoloration of the bar.

In freezing weather oil will thicken, making it necessary to thin bar and chain oil with a small amount (5 to 10%) of #1 Diesel Fuel or kerosene. Bar and chain oil must be free flowing for the oil system to pump enough oil for adequate lubrication.

Genuine Poulan or Poulan PRO bar and chain oil is recommended to protect your unit against excessive wear from heat and fric- tion. Poulan or Poulan PRO oil resists high temperature thinning.

If Poulan or Poulan PRO bar and chain oil is not available, use a good grade SAE 30 oil.

SNever use waste oil for bar and chain lubri- cation.

SAlways stop the engine before removing the oil cap.

CHAIN BRAKE

Ensure chain brake is disengaged by pulling the front hand guard back toward the front han- dle as far as possible. The chain brake must be disengaged before cutting with the saw.

WARNING: The chain must not move when the engine runs at idle speed. If the chain moves at idle speed refer to CAR- BURETOR ADJUSTMENT within this manual. Avoid contact with the muffler. A hot muffler can cause serious burns.

To stop the engine move the ON/STOP switch to the STOP position.

To start the engine hold the saw firmly on the ground as illustrated. Make sure the chain is free to turn without contacting any object.

Use only 15-- 18(40 -- 45 cm) of rope per pull.

Hold saw firmly while pulling starter rope. Starter Rope Handle

Left Hand on Front Handle

Right Foot Through Rear Handle

WARNING: Do not attempt to throw or drop--start the chain saw. Doing so will put the operator at risk of serious injury due to loss of control of the chain saw.

9

Page 9
Image 9
Poulan 952802031, 952802030, 952802124 Before Starting Engine Fueling Engine, Fuel Requirements, BAR and Chain Lubrication

952802124, 952802030, 952802031 specifications

Poulan, a respected name in outdoor power equipment, offers a range of innovative products designed for lawn care and maintenance. Among its extensive lineup, the models 952802124, 952802030, and 952802031 stand out due to their powerful functionalities and user-friendly features. Each of these models incorporates advanced technologies aimed at enhancing the user experience and ensuring efficient operation.

The Poulan 952802124 model is primarily recognized for its robust performance. It boasts a powerful engine that allows it to handle various tasks with ease. Whether you need to tackle thick grass or overgrown weeds, this model has the capability to deliver optimal results. It features a durable cutting deck that provides an even cut while minimizing the need for multiple passes, ultimately saving time and effort.

In terms of user comfort, the 952802124 integrates ergonomic handles designed for better control and reduced fatigue. This is especially beneficial for extended periods of use, making it a reliable choice for both homeowners and professional landscapers. Additionally, the model is equipped with a quick-start technology, ensuring that you can get to work without unnecessary delays.

The Poulan 952802030 model places a strong emphasis on versatility. It comes with interchangeable attachments, allowing users to customize their equipment according to specific needs. Whether it's leaf blowing, mulching, or trimming, the 952802030 adapts to various tasks efficiently. This flexibility makes the model suitable for different seasons and environments, providing year-round functionality.

Moreover, state-of-the-art safety features are integrated into the design of the 952802030, including a safety lock mechanism that prevents accidental starts, ensuring the user's safety during operation. The lightweight construction also allows for easy maneuverability, making it an ideal choice for navigating tight spaces or uneven terrain.

Meanwhile, the Poulan 952802031 rounds out this trio with its emphasis on energy efficiency. The model is engineered to reduce fuel consumption without compromising performance. It incorporates technologies designed to minimize emissions, aligning with environmentally-friendly practices and regulations. The 952802031 also features an easy-to-access air filter, which simplifies maintenance and prolongs the life of the engine.

In summary, the Poulan 952802124, 952802030, and 952802031 represent excellent choices in the realm of outdoor power equipment. With an emphasis on performance, versatility, safety, and environmental responsibility, these models are well-suited for a variety of lawn care needs, making them valuable investments for consumers. Each model embodies Poulan's commitment to quality and innovation, ensuring satisfaction for both casual users and professionals alike.