OPERATION

TO ADJUST SKID PLATES (See Fig. 16)

NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.

Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow in normal conditions, such as a paved driveway or sidewalk, place skid plates in the highest position (lowest scraper clearance) to give a 1/8" clearance between the scraper bar and the ground. Use a middle position if the surface to be cleared is uneven.

NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property damage or damage to the snow thrower.

• If snow thrower must be operated over gravel surface,

use extra caution and be sure skid plates are adjusted

to lowest (highest scraper clearance) position.

WARNING: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

CAUTION: Alcohol blended fuels (called gaso- hol or using ethanol or methanol) can attract moisture which leads to separation and forma- tion of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Empty the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

1.Shut off engine and wait for all moving parts to stop.

2.Adjust skid plates by loosening the hex nuts, then moving skid plate to desired position. Be sure both plates are adjusted evenly. Tighten securely.

HIGH POSITION

 

(LOW GROUND

 

CLEARANCE)

 

 

AUGER

 

HOUSING

 

SCRAPER BAR

HEX

SKID PLATE

NUTS

LOW POSITION (HIGH GROUND CLEARANCE)

FIG. 16

SCRAPER BAR (See Fig. 16)

CHOKE CONTROL

SAFETY

IGNITION

KEY

RECOIL

STARTER

HANDLE

THROTTLE PRIMER ENGINE OIL FILL CAP / DIPSTICK

GASOLINE

FILLER CAP

FUEL SHUT-

OFF VALVE

STARTER BUTTON

POWER CORD PLUG

The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a damaged or worn scraper bar.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 17)

The engine on your snow thrower has been shipped, from the factory, already filled with oil.

1.Check engine oil with snow thrower on level ground.

2.Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

To change engine oil, see “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.

ADD GASOLINE (See Fig. 17)

Fill fuel tank to bottom of tank filler neck. Do not over- fill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

11

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.

FIG. 17

TO START ENGINE

Be sure fuel shut-off valve is in the “OPEN” position.

Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current.

Be sure your house is a 120 Volt A.C. three-wire grounded system. If you are uncertain, consult a licensed electrician.

WARNING: Do not use the electric starter if your house is not a 120 Volt A.C. three-wire grounded system. Seri- ous personal injury or damage to your snow thrower could result.

Page 11
Image 11
Poulan 421899, 96192001706 owner manual Before Starting the Engine, To Start Engine

96192001706, 421899 specifications

The Poulan 421899,96192001706 is a powerful and versatile outdoor tool designed to meet the needs of both homeowners and professionals. This particular product is known for its reliability and effectiveness in various landscaping tasks, including trimming, pruning, and even cutting through tougher branches.

One of the standout features of this model is its robust engine, which provides ample power to tackle challenging outdoor jobs. The engine is designed for optimal performance, ensuring that users can complete their tasks swiftly without sacrificing efficiency. The combination of a strong engine and lightweight design allows for prolonged use without significant fatigue, making it a favorite among those who require a dependable tool for extended periods.

In terms of technology, the Poulan 421899,96192001706 boasts advanced anti-vibration features that significantly enhance user comfort. This technology minimizes the amount of vibration felt during operation, allowing for smoother handling and greater precision when trimming or cutting. Users will appreciate how this feature reduces strain on their arms and hands, making it easier to handle the tool over long durations.

The design of the Poulan 421899,96192001706 also prioritizes user-friendliness. The easy-start system ensures that the tool can be fired up with minimal effort, which can be particularly beneficial for those who may struggle with traditional starting methods. Additionally, the ergonomic handle provides a comfortable grip, further enhancing control and maneuverability.

Durability is another key characteristic of this model. Built from high-quality materials, it is designed to withstand the rigors of outdoor use, whether in residential settings or more demanding commercial environments. The materials used in construction are resistant to wear and tear, ensuring that the tool lasts for many years with proper maintenance.

Another notable aspect of the Poulan 421899,96192001706 is its versatility. With compatible attachments and a range of performance options, it can easily adapt to various tasks. This multifunctional capability makes it an invaluable addition to any toolkit, whether for landscaping, gardening, or general outdoor maintenance.

In conclusion, the Poulan 421899,96192001706 is a well-rounded outdoor tool that combines power, advanced technology, and ease of use. Its robust engine, anti-vibration features, and ergonomic design make it a top choice for those looking for efficiency and comfort in their outdoor tasks. With its durability and versatility, it stands out in the market, proving itself to be a reliable partner for both amateur gardeners and professional landscapers alike.