Manuals / Poulan / Lawn and Garden / Snow Blower

Poulan 422080, 96192002201, XT5524ES owner manual Handles, Part, Description, 180480

Models: XT5524ES 422080 96192002201

1 40

Download 40 pages 50.79 Kb

Page 28

Image 28

REPAIR PARTS SNOW THROWER - - MODEL NUMBER XT5524ES (96192002201)

HANDLES

		KEY	PART	DESCRIPTION
		NO.	NO.	DESCRIPTION
1		1	180480	IMPELLER ROD ASSEMBLY
3		2	405740	TRACTION ROD ASSEMBLY
3		3	180445	SHIFTER ROD TOP
		4	187716	SHIFTER ROD BOTTOM
		5	180447	SPRING SLEEVE
		6	178669	IMPELLER SPRING
	8	7	180926	TRACTION SPRING
	8	8	72270506	CARRIAGE BOLT 5/16−18 X .75
		8	72270506	CARRIAGE BOLT 5/16−18 X .75
		9	155377	NUT 5/16−18
9		10	169675	RETAINER
4
		5

10	7

6	01.12.001-A

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 28

Page 28

Image 28

Poulan 422080, 96192002201, XT5524ES owner manual Handles, Part, Description, 180480

Contents

SNOW THROWER IMPORTANT MANUALXT5524ES Do Not Throw AwayPreparation TrainingOperation TABLE OF CONTENTS PRODUCT SPECIFICATIONSMaintenance and Storage CUSTOMER RESPONSIBILITIESASSEMBLY / PRE-OPERATION HOW TO SET UP YOUR SNOW THROWERPARTS PACKED SEPARATELY IN CARTON REMOVE SNOW THROWER FROM CARTONINSTALL SPEED CONTROL ROD See Figs. 1 and ASSEMBLY / PRE-OPERATIONUNFOLD UPPER HANDLE INSTALL AUGER CONTROL ROD See Figs. 5 and ASSEMBLY / PRE-OPERATIONCHECK TIRE PRESSURE OPERATION KNOW YOUR SNOW THROWERMEETS A.N.S.I. SAFETY REQUIREMENTS OPERATIONHOW TO USE YOUR SNOW THROWER OPERATIONTO USE CHOKE CONTROL See Fig STOPPINGUSING THE CLEAN-OUTTOOL See Fig OPERATIONTO THROW SNOW See Fig. TO MOVE FORWARD AND BACKWARD See FigBEFORE STARTING THE ENGINE TO ADJUST SKID PLATES See FigOPERATION SCRAPER BAR See FigSNOW THROWING TIPS OPERATIONBEFORE STOPPING IF RECOIL STARTER HAS FROZENMAINTENANCE GENERAL RECOMMENDATIONSBEFORE EACH USE LUBRICATIONCLEANING ENGINEMAINTENANCE V-BELTSSERVICE AND ADJUSTMENTS 2.Remove safety ignition keyTO ADJUST SNOW THROWER HEIGHT SNOW THROWERSERVICE AND ADJUSTMENTS TO REPLACE BELTS See FigSTORAGE OTHERENGINE SNOW THROWERTROUBLESHOOTING Loss of powerDoes not start Engine idles orSERVICE NOTES AUGER HOUSING / IMPELLER ASSEMBLY PART AUGER HOUSING / IMPELLER ASSEMBLYDESCRIPTION AUGER HOUSING / IMPELLER ASSEMBLY PARTDESCRIPTION PARTAUGER HOUSING / IMPELLER ASSEMBLY PARTDESCRIPTION PARTPART CONTROL PANEL / CHUTEDESCRIPTION PART CONTROL PANEL / CHUTEDESCRIPTION HANDLES PARTDESCRIPTION PARTHANDLES 01.08.002-EHANDLES PARTDESCRIPTION 180480HANDLES PARTDESCRIPTION PARTDRIVE DRIVE PARTDESCRIPTION PARTDRIVE CHASSIS / ENGINE / PULLEYS PARTDESCRIPTION ENGINE TECUMSEH MODEL LH195SP-67510DCHASSIS / ENGINE / PULLEYS PARTDESCRIPTION 192213PART WHEELSDESCRIPTION BAG OF PARTS SAFETY IGNITION KEYPART DESCRIPTIONPART DECALSDESCRIPTION SERVICE NOTES SERVICE NOTES LIMITED WARRANTY