SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 24)

Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

KLIK PIN

OUTER HOLE

 

INNER

 

HOLE

WHEEL

WHEEL HUB

FIG. 24

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service centre.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service centre, which has proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

18

Page 18
Image 18
Poulan 96194000600 owner manual Storage

96194000600 specifications

The Poulan 96194000600 is a standout lawn mower that exemplifies quality and innovation in outdoor power equipment. Designed to meet the diverse needs of homeowners and landscape enthusiasts, this mower combines advanced features and technologies to deliver impressive performance and ease of use.

One of the main features of the Poulan 96194000600 is its powerful engine. Equipped with a reliable gas engine, it provides robust power for mowing various types of grass and terrain. This ensures that even tougher lawns are tackled efficiently, allowing homeowners to achieve that well-manicured look with minimal effort.

The mower is designed with a wide cutting deck, typically measuring around 21 inches. This size not only enhances the mower’s ability to cover more ground in less time but also provides a clean and even cut. The adjustable cutting height feature allows users to select the optimal height for their lawn, catering to different grass types and individual preferences.

In terms of technology, the Poulan 96194000600 incorporates a self-propulsion system. This feature significantly reduces the amount of effort required to push the mower, making it easier to navigate hilly or uneven terrain. With variable speed control, users can adjust the pace of the mower to suit their walking speed, enhancing comfort and control during operation.

Durability is another hallmark of the Poulan 96194000600. Constructed with rugged materials, this mower is built to withstand the rigors of regular use. Its solid frame and high-quality blades are designed for longevity, ensuring that owners can rely on this equipment season after season.

User convenience is a priority in the design of the Poulan 96194000600. The mower features ergonomic handles, enhancing comfort during operation. Additionally, it often includes features such as tool-free height adjustments and easy-to-empty grass bags, streamlining the maintenance process.

With its combination of power, versatility, and user-friendly design, the Poulan 96194000600 is an ideal choice for those seeking a dependable lawn mower. Whether you have a small yard or a larger garden, this mower promises to deliver exceptional performance, making lawn care a more enjoyable and efficient task.