SThis saw is equipped with a chain brake. The brake is designed to stop the chain if

kickback occurs.

S The inertia--activated chain brake is activated if the front hand guard is pushed forward, either manually (by hand) or automatically (by sudden movement).

S If the brake is already activated, it is disengaged by pulling the front hand guard back toward the front handle as far as possible.

SWhen cutting with the saw, the chain brake must be disengaged.

Disengaged

Engaged

Braking function control CAUTION: The chain brake must be

checked several times daily. The engine must be running when performing this proce- dure. This is the only instance when the saw should be placed on the ground with the en- gine running.

Place the saw on firm ground. Grip the rear handle with your right hand and the front han- dle with your left hand. Apply full throttle by fully depressing the throttle trigger. Activate the chain brake by turning your left wrist against the hand guard without releasing your grip around the front handle. The chain should stop immediately.

Inertia activating function control

WARNING: When performing the following procedure, the engine must be turned off.

Grip the rear handle with your right hand and the front handle with your left hand. Hold the chain saw approximately 14″ (35 cm) above a stump or other wooden surface. Release your grip on the front handle and use the weight of the saw to let the tip of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate.

OPERATING TIPS

SCheck chain tension before first use, after 1 minute of operation, and each time be- fore you start the chain saw. See CHAIN TENSION in the ASSEMBLY section.

SCut wood only. Do not cut metal, plastics,

masonry, non-wood building materials, etc.

SStop the saw if the chain strikes a foreign object. Inspect the saw and repair or re- place parts as necessary. If the chain jumps off the guide bar, inspect the chain for damaged drive links before reinstalling. Burrs on drive links, which prevent them from entering the groove of the guide bar, can be removed with a flat file.

SKeep the chain out of dirt and sand. Even a small amount of dirt will dull a chain, increase the possibility of kickback, and require chain sharpening or replacement.

SPractice cutting a few small logs using the following techniques to get the “feel” of us- ing your saw before you begin a major sawing operation.

S Squeeze the throttle trigger and allow the engine to reach full speed before cutting.

S Begin cutting with the saw frame against the log.

S Keep the engine at full speed the entire time you are cutting.

S Allow the chain to cut for you. Exert only light downward pressure. If you force the cut, damage to the bar, chain, or en- gine can result.

S Release the throttle trigger as soon as the cut is completed, allowing the en- gine to idle. If you run the saw at full throttle without a cutting load, unneces- sary wear can occur to the chain, bar, and engine. It is recommended that the engine not be operated for lon- ger than 30 seconds at full throttle.

S To avoid losing control when cut is com- plete, do not put pressure on saw at end

of cut.

S Stop the engine before setting the saw down after cutting.

TREE FELLING TECHNIQUES

WARNING: Check for broken or dead branches which can fall while cutting causing serious injury. Do not cut near build- ings or electrical wires if you do not know the direction of tree fall, nor cut at night since you will not be ale to see well, nor during bad weather such as rain, snow, or strong winds, etc. If the tree makes contact with any utility line, the utility company should be notified immediately.

SCarefully plan your sawing operation in ad- vance.

SClear the work area. You need a clear area

all around the tree so you can have secure footing.

SThe chain saw operator should keep on the uphill side of the terrain as the tree is likely to roll or slide downhill after it is felled.

SStudy the natural conditions that can cause the tree to fall in a particular direction.

Natural conditions that can cause a tree to fall in a particular direction include:

SThe wind direction and speed.

S The lean of the tree. The lean of a tree might not be apparent due to uneven or sloping terrain. Use a plumb or level to de- termine the direction of tree lean.

SWeight and branches on one side. S Surrounding trees and obstacles.

Look for decay and rot. If the trunk is rotted, it can snap and fall toward the operator. Check for broken or dead branches which can fall on you while cutting.

Make sure there is enough room for the tree to fall. Maintain a distance of 2-1/2tree lengths from the nearest person or other objects. En- gine noise can drown out a warning call.

Remove dirt, stones, loose bark, nails, sta- ples, and wire from the tree where cuts are to be made.

11

Page 10 Page 12
Page 11
Image 11
Poulan 966513901 Braking function control Caution The chain brake must be, Inertia activating function control
Page 10 Page 12

966513901 specifications

The Poulan 966513901 is a powerful and versatile chainsaw designed for both professional landscapers and enthusiastic DIYers. Renowned for its durability and efficiency, this model is engineered to tackle a variety of cutting tasks, from felling trees to trimming branches and cutting firewood.

One of the standout features of the Poulan 966513901 is its robust engine. Powered by a high-performance gas engine, this chainsaw delivers impressive horsepower, enabling it to cut through tough materials with ease. The engine is also designed to provide efficient fuel consumption, which translates to longer operating times and reduced refueling intervals, making it ideal for extensive jobs.

The chainsaw features a 18-inch guide bar, optimizing cutting length while maintaining a manageable weight. This balance enhances maneuverability, allowing users to handle the chainsaw comfortably for extended periods. Additionally, the chainsaw comes equipped with a chain brake, a crucial safety feature that helps protect the user in the event of kickback. This brake engages automatically when the chainsaw is dropped or tilted unexpectedly, providing an additional layer of protection during operation.

Another noteworthy characteristic of the Poulan 966513901 is its Easy Start technology. This innovation simplifies the starting process, allowing users to start the engine with minimal effort. This feature is particularly beneficial for those who may struggle with traditional pull-start mechanisms, making it accessible for users of varying experience levels.

The chainsaw also includes an adjustable automatic oiler, ensuring that the chain remains adequately lubricated during operation. This not only extends the lifespan of the chain but also enhances cutting efficiency. The oil reservoir is easy to access, enabling quick refills without interrupting work flow.

In terms of weight, the Poulan 966513901 strikes a balance between power and portability. It is lightweight enough for easy handling, yet robust enough to handle demanding tasks. This makes it a suitable choice for both professional and home use.

Overall, the Poulan 966513901 stands out in the crowded market of chainsaws due to its powerful performance, user-friendly features, and robust design. Whether you are cutting firewood, maintaining your property, or undertaking more significant landscaping projects, this chainsaw is a reliable companion that delivers efficiency and ease of use.
Top Page Image Contents