ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1) 1/2" wrench

Utility knife

(1) 3/4" wrench

Tire pressure gauge

Pliers

 

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

Remove all accessible loose parts and parts cartons from carton.

Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels fl at.

Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

Slide extension shaft onto lower steering shaft.

Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

Position front wheels of the tractor so they are pointing straight forward.

Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

Assemble large fl at washer, 5/16 lock washer, 5/16 hex bolt and tighten securely.

Snap steering wheel insert into center of steering wheel.

Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

INSERT

5/16 HEX BOLT

5/16 LOCK WASHER

LARGE FLAT

WASHER

STEERING

WHEELSTEERING BOOT

TABS

ADAPTER

EXTENSION

SHAFT

LOWER

STEERING

SHAFT

TAB

SLOTS

FIG. 1

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment bolt.

Remove adjustment bolt, lock washer and fl at washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

Pivot seat and pan forward and assemble adjust- ment bolt, lockwasher and fl at washer loosely. Do not tighten

Lower seat into operating position and sit on seat.

Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

Get off seat without moving its adjusted position.

Raise seat and tighten adjustment bolt securely.

6

Page 6
Image 6
Poulan PB1638LT manual Tools Required for Assembly, To Remove Tractor from Carton, Before Removing Tractor from Skid

PB1638LT specifications

The Poulan PB1638LT is a highly regarded leaf blower designed to tackle various outdoor tasks with efficiency and ease. This powerful outdoor tool is particularly favored among homeowners and professionals alike for its combination of power, versatility, and user-friendly features.

At the heart of the PB1638LT is its robust 38cc, 2-cycle engine, delivering impressive air speeds that can reach up to 200 miles per hour. This substantial air velocity enables users to quickly clear debris, leaves, and grass clippings from lawns, driveways, and patios, making yard maintenance an effortless task. The leaf blower's vacuum and mulcher capabilities further enhance its functionality, allowing users to not only blow away debris but also to collect and shred leaves into fine mulch, which can be used to enrich garden beds.

One of the standout features of the Poulan PB1638LT is its lightweight design, weighing in at just 11 lbs. This manageable weight ensures reduced fatigue during extended use, promoting comfort even when tackling larger areas. The inclusion of a shoulder strap also aids in distributing weight evenly, making the blower easier to maneuver during operation.

The ergonomic design of the PB1638LT cannot be overlooked. It incorporates a comfortable grip and easy-to-reach throttle control, enabling users to operate it smoothly with one hand. This functional design is particularly beneficial for those who may have limited strength or mobility, as it simplifies the operation without sacrificing power.

Poulan's commitment to technology is evident in the PB1638LT's Advanced Fuel System. This feature enhances fuel efficiency while reducing emissions, making it a more environmentally friendly choice compared to conventional blowers. The system helps maintain optimum engine performance and longevity, ensuring that the PB1638LT remains a reliable tool for years to come.

To sum it up, the Poulan PB1638LT leaf blower stands out as a versatile and powerful tool suitable for various outdoor cleaning tasks. With its formidable engine performance, vacuum and mulching capabilities, lightweight design, and user-friendly features, it is an excellent investment for anyone looking to maintain a tidy yard or garden effortlessly. Whether you're a homeowner wanting to keep your property looking pristine or a professional landscaper in need of a dependable blower, the PB1638LT is a name to consider.