SERVICE AND ADJUSTMENTS

To Replace Mower Drive Belt (See Fig. 24)

MOWER DRIVE BELT REMOVAL

1.Park tractor on a level surface. Engage parking brake.

2.Lower attachment lift lever to its lowest position.

3.Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface.

4.Remove belt from clutch pulley (M), both mandrel pul- leys (R) and all idler pulleys (S).

MOWER DRIVE BELT INSTALLATION

1.Install belt around both mandrel pulleys (R) and around idler pulleys (S) as shown.

2.Install belt onto clutch pulley (M).

IMPORTANT: Check belt for proper routing in all mower pulley grooves.

3. Raise attachment lift lever to highest position.

'

-

&

12

'

! %

"

0

#

+

,$

FIG. 24

TO REPLACE MOTION BELT DRIVE (See Fig. 25)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

Remove belt from stationary idler (A) and clutching idler (B).

Remove belt from centerspan idler (C).

Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades (D).

Remove belt downward from engine pulley (E).

Slide belt toward rear of tractor, off the steering plate

(F) and remove from tractor.

BELT INSTALLATION -

Install new belt from tractor rear to front, over the steer- ing plate (F) and above clutch brake pedal shaft (G).

Pull belt toward front of tractor and roll belt onto engine pulley (E).

Pull belt toward rear of tractor. Carefully work belt down around transmission cooling fan and onto the input pulley (D). Be sure belt is inside the belt keeper.

Install belt on centerspan idler (C).

Install belt through stationary idler (A) and clutching idler (B).

Make sure belt is in all pulley grooves and inside all belt guides and keepers.

Install mower (See “TO INSTALL MOWER” in this section of manual).

TO CHECK BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

1.Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

2.Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manu- ally push the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a qualified service center.

E

F

A

B G

C

D

22

FIG. 25

 

Page 22
Image 22
Poulan PB195H42LT To Replace Mower Drive Belt See Fig, To Replace Motion Belt Drive See Fig, To Check Brake, Belt Removal

PB195H42LT specifications

The Poulan PB195H42LT is a robust riding lawn mower designed to provide an efficient and enjoyable mowing experience. With an impressive blend of power, durability, and advanced features, this mower caters to homeowners with substantial lawn care needs.

At the heart of the PB195H42LT is its reliable 195cc Briggs & Stratton engine. This engine is known for its durability and consistent performance, allowing for effortless starts and smooth operation. The engine provides ample power to tackle tough grass and uneven terrain, ensuring a clean and even cut every time.

One of the standout features of the Poulan PB195H42LT is its 42-inch cutting deck. This wide mowing deck enables users to cover larger areas in less time while providing a clean cut. The deck is designed with an innovative cutting system that utilizes two sharp blades, which not only promotes a fine finish but also helps in mulching grass clippings effectively.

The mower also boasts a 6-position cutting height adjustment feature, allowing users to customize their lawn mowing experience. Whether you're looking for a close trim or a higher cut, the adjustable heights suit various grass types and conditions, providing flexibility for different lawn care tasks.

The PB195H42LT incorporates a foot-controlled hydrostatic transmission that delivers seamless speed changes. This technology allows for smooth acceleration and deceleration without the need for shifting gears. As a result, operators can navigate their yards with precision and comfort, especially around obstacles such as flower beds and trees.

Comfort is a priority in the design of the PB195H42LT. The mower features an ergonomic seat with ample cushioning, ensuring a pleasant riding experience, even during extended mowing sessions. Additionally, the easy-to-use controls are conveniently located for quick adjustments, minimizing distractions when operating the machine.

Safety is also a significant consideration with this mower. It includes features such as an operator presence system that ensures the engine shuts off if the operator leaves the seat, thereby preventing accidents.

In summary, the Poulan PB195H42LT combines powerful performance with user-friendly design. With its efficient engine, versatile cutting deck, flawless transmission system, and comfortable features, this riding lawn mower is an ideal choice for homeowners who prioritize quality and efficiency in lawn maintenance. Its reliable construction and innovative technology make it a valuable addition to any gardening toolkit.