ASSEMBLY

Push down on seat to engage pads in slots and pull seat towards rear of tractor.

Raise seat and tighten bolt securely.

Remove tape and discard.

Lower seat into operating position and sit on seat. Press clutch/brake pedal all the way down. If operating position is not comfortable, adjust seat.

To adjust seat: Grasp adjustment handle and pull up, slide seat to desired position and release adjustment handle.

SLOT

 

TAPE

PAD

 

 

FLAT

 

 

WASHER

 

 

SEAT PAN

 

BOLT

TAB

ADJUSTMENT

HANDLE

 

 

Fig. 3

CHECK BATTERY (See Fig. 4)

Lift seat pan to raised position.

If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in MAINTENANCE section of this manual for charging instructions).

SEAT PAN

LABEL

TERMINAL

TERMINAL

FIG. 4

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

TO ROLL TRACTOR OFF SKID (See Op- eration section for location and function of controls)

Press lift lever plunger and raise attachment lift lever to its highest position.

Release parking brake by depressing clutch/brake pedal.

Place freewheel control in "transmission disengaged position" (See “TO TRANSPORT” in the Operation section of this manual).

Roll tractor forward off skid.

Remove banding holding the deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

Be sure all the above assembly steps have been com- pleted.

Check engine oil level and fill fuel tank with gasoline.

Place freewheel control in "transmission engaged" position (see "TO TRANSPORT" in Operation section of this manual).

Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

Place motion control lever in neutral (N) position.

Press lift lever plunger and raise attachment lift lever to its highest position.

Remove key from bag and start the engine (see "TO START ENGINE" in the Operation section of this manual). After engine has started, move throttle control to idle (slow) position.

Release parking brake.

Slowly move the motion control lever forward and slowly drive tractor off skid.

Apply brake to stop tractor, set parking brake and place motion control lever in neutral position.

Turn ignition key to "STOP" position.

Continue with the instructions that follow.

7

Page 7
Image 7
Poulan PB195H42LT manual Check Battery See Fig

PB195H42LT specifications

The Poulan PB195H42LT is a robust riding lawn mower designed to provide an efficient and enjoyable mowing experience. With an impressive blend of power, durability, and advanced features, this mower caters to homeowners with substantial lawn care needs.

At the heart of the PB195H42LT is its reliable 195cc Briggs & Stratton engine. This engine is known for its durability and consistent performance, allowing for effortless starts and smooth operation. The engine provides ample power to tackle tough grass and uneven terrain, ensuring a clean and even cut every time.

One of the standout features of the Poulan PB195H42LT is its 42-inch cutting deck. This wide mowing deck enables users to cover larger areas in less time while providing a clean cut. The deck is designed with an innovative cutting system that utilizes two sharp blades, which not only promotes a fine finish but also helps in mulching grass clippings effectively.

The mower also boasts a 6-position cutting height adjustment feature, allowing users to customize their lawn mowing experience. Whether you're looking for a close trim or a higher cut, the adjustable heights suit various grass types and conditions, providing flexibility for different lawn care tasks.

The PB195H42LT incorporates a foot-controlled hydrostatic transmission that delivers seamless speed changes. This technology allows for smooth acceleration and deceleration without the need for shifting gears. As a result, operators can navigate their yards with precision and comfort, especially around obstacles such as flower beds and trees.

Comfort is a priority in the design of the PB195H42LT. The mower features an ergonomic seat with ample cushioning, ensuring a pleasant riding experience, even during extended mowing sessions. Additionally, the easy-to-use controls are conveniently located for quick adjustments, minimizing distractions when operating the machine.

Safety is also a significant consideration with this mower. It includes features such as an operator presence system that ensures the engine shuts off if the operator leaves the seat, thereby preventing accidents.

In summary, the Poulan PB195H42LT combines powerful performance with user-friendly design. With its efficient engine, versatile cutting deck, flawless transmission system, and comfortable features, this riding lawn mower is an ideal choice for homeowners who prioritize quality and efficiency in lawn maintenance. Its reliable construction and innovative technology make it a valuable addition to any gardening toolkit.