To Replace Headlight Bulb, To Replace Fuse

SERVICE AND ADJUSTMENTS

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) ter- minal with remaining hex bolt and keps nut. Tighten securely.

SEAT PAN

FIG. 28

	TERMINAL	KEPS
		NUT
	COVER

HEX

BOLT

POSITIVE (RED)	NEGATIVE
CABLE	(BLACK) CABLE

FIG. 29

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 30)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

FIG. 30

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 31)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

•Check that holes “A” in governor control lever and hole in governor plate line-up. If holes “A” are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten clamp screw securely.

	GOVERNOR	GOVERNOR
	CONTROL LEVER	GOVERNOR
	CONTROL LEVER	CONTROL PLATE
		CONTROL PLATE
HOLES “A”	CLAMP	THROTTLE
	SCREW	CABLE

FIG. 31

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjustment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

High speed stop is factory adjusted. Do not adjust - dam- age may result.

IMPORTANT:NEVERTAMPERWITHTHEENGINEGOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACTYOUR NEAREST AUTHORIZED SERVICE CENTER/ DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS.

PO18H42STA specifications

The Poulan PO18H42STA is a powerful and versatile lawn tractor designed to make mowing large lawns a breeze. With its robust engine and innovative features, this machine stands out as an exceptional choice for homeowners looking for efficiency and reliability in lawn care.

At the heart of the Poulan PO18H42STA is its 18.5 HP Briggs & Stratton engine, which provides ample power to tackle tough mowing tasks with ease. The engine is known for its durability and performance, ensuring that users can rely on it season after season. Whether you're dealing with thick grass or uneven terrain, the engine's strong output makes it well-suited for a variety of lawn conditions.

A key feature of the PO18H42STA is its 42-inch cutting deck. This deck strikes the perfect balance between maneuverability and cutting width, allowing users to navigate through tight spaces while still covering large areas efficiently. The cutting height can be easily adjusted using a manual lever, offering six different settings for a customized mowing experience tailored to the specific needs of your lawn.

The Poulan PO18H42STA also incorporates a hydrostatic transmission, which provides smooth, precise control over speed and direction. This technology eliminates the need for gear shifting, allowing for seamless operation as you move forward or reverse. It enhances the overall user experience, making it suitable for both seasoned operators and those new to lawn tractors.

For added comfort, this model features a comfortable high-back seat designed to reduce fatigue during longer mowing sessions. The seat is adjustable, allowing users to find their optimal driving position. Additionally, the tractor is equipped with ergonomic controls, making it user-friendly and easy to operate.

In terms of maintenance, the PO18H42STA is designed with accessibility in mind. The engine compartment opens easily for routine checks, and the cutting deck can be removed without hassle for cleaning or blade maintenance. This attention to design simplifies upkeep, ensuring that your lawn tractor remains in top condition.

Overall, the Poulan PO18H42STA is a reliable lawn tractor that combines power, convenience, and comfort. With its strong engine, versatile cutting deck, and user-friendly features, it is an excellent investment for anyone looking to maintain a beautiful lawn with minimal effort. Whether you're mowing grassy expanses or navigating around flower beds, this lawn tractor delivers outstanding performance and versatility.

Poulan PO18H42STA manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Models: PO18H42STA