Poulan PO18H42STA manual To Replace Motion Drive Belt See Fig, To Check Brake, To Adjust Brake

SERVICE AND ADJUSTMENTS

TO CHECK BRAKE

•Park tractor on a level, dry concrete or paved surface, depress clutch/brake pedal all the way down and en- gage parking brake.

•Disengage transmission by placing freewhel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, the brake needs to be adjusted or the pads need to be replaced.

TO ADJUST BRAKE

•Depress clutch/brake pedal all the way down and en- gage parking brake.

•Measure distance between brake operating arm and nut “A” on brake rod.

•If distance is other than 1-9/16", loosen jam nut and turn nut “A” until distance becomes 1-9/16". Retighten jam nut against nut “A”.

•Engage transmission by placing freewheel control in “transmission engaged” position.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is necessary. Replace brake pads or contact a qualified service center.

WITH PARKING BRAKE “ENGAGED”

NUT “A”

1-9/16” JAM NUT

OPERATING

ARM

DO NOT TOUCH THIS NUT. IF FURTHER

BRAKE ADJUSTMENT IS NECESSARY CON-

TACT YOUR NEAREST AUTHORIZED SERVICE

CENTER/DEPARTMENT

FIG. 23

TO REPLACE MOTION DRIVE BELT (See Fig. 24)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Remove belt from stationary idler and clutching idler.

•Remove belt downward from around engine pulley.

•Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades.

•Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

•Carefully work new belt down around transmission cooling fan and onto the input pulley.

•Slide belt into the center span keeper.

•Pull belt toward front of tractor and roll around the top groove of engine pulley.

•Install belt through stationary idler and clutching idler.

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this sec- tion of manual).

ENGINE

PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

TRANSMISSION

INPUT PULLEYCENTER SPAN KEEPER

FIG. 24

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 25)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

•Start engine and move motion control lever until tractor does not move forward or backward.

•Hold motion control lever in that position and turn engine off.

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (N) (lock gate) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satis- fied.

21