SERVICE AND ADJUSTMENTS
TO ADJUST STEERING WHEEL
ALIGNMENT
If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.
FRONT WHEEL TOE-IN/CAMBER
The front wheel
TO REMOVE WHEEL FOR REPAIRS (See Fig. 28)
•Block up axle securely.
•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).
•Repair tire and reassemble.
•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.
•Replace washers and snap retaining ring securely in axle groove.
•Replace axle cover.
NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.
WASHERS
RETAINING
RING
AXLE
COVER
SQUARE KEY 
(REAR WHEEL ONLY)
FIG. 28
TO START ENGINE WITH A WEAK BATTERY (See Fig. 29)
WARNING:
•Connect one end of the BLACK cable to the NEGATIVE
•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.
TO REMOVE CABLES, REVERSE ORDER -
•BLACK cable first from chassis and then from the fully charged battery.
•RED cable last from both batteries.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
WEAK OR DEAD |
| FULLY CHARGED | |||||||||||||||||||||||||
BATTERY |
| BATTERY | |||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
FIG. 29
REPLACING BATTERY (See Fig. 30)
WARNING: Do not short battery ter- minals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.
Positive terminal must be connected first to prevent sparking from accidental grounding.
•Lift hood to raised position.
•Remove terminal guard.
•Disconnect BLACK battery cable then RED battery cable and carefully remove battery from tractor.
•Install new battery with terminals in same position as old battery.
•Reinstall terminal guard.
•First connect RED battery cable to positive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely.
•Connect BLACK grounding cable to negative
•Close terminal access doors.
•Close hood.
batteries. Always wear eye protection when around batteries.
If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).
If “jumper cables” are used for emergency starting, follow this procedure:
IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT
TERMINAL ACCESS DOOR
KEPS NUT
HEX BOLT
POSITIVE (RED)
CABLE
SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.
TO ATTACH JUMPER CABLES -
• Connect one end of the RED cable to the POSITIVE |
TERMINAL GUARD
NEGATIVE (BLACK)
CABLE
(+) terminal of each |
short against tractor chassis. |
FIG. 30
24
