KEY Part Description, Auger Housing, Scrapper BAR | Poulan PP291E30

REPAIR PARTS SNOW THROWER - MODEL PP291E30 (96198003000)

AUGER HOUSING / IMPELLER ASSEMBLY

1

		KEY	PART
		NO.	NO.	DESCRIPTION
		1	404930X428	AUGER HOUSING
	3 (5x)	2	404933X479	SCRAPPER BAR
	3 (5x)	3	72270505	CARRIAGE BOLT 5/16−18 X .625
	4 (5x)	3	72270505	CARRIAGE BOLT 5/16−18 X .625
	4 (5x)	4	155377	NUT 5/16−18
		4	155377	NUT 5/16−18

2

01.07.003-A

2	3

1

1

2

		KEY	PART
		NO.	NO.	DESCRIPTION
		1	420478	AUGER BEARING
	3	2	411939	BEARING PLUG
	3	3	179582	SCREW 5/16−18 X 1.00
		3	179582	SCREW 5/16−18 X 1.00
		01.07.024-B

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

21

Image 21

Poulan PP291E30 owner manual KEY Part Description, Auger Housing, Scrapper BAR, Auger Bearing, Bearing Plug

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper Handle Install Auger Control ROD See Figs Install Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Know Your Snow Thrower Operation Recoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See Fig To Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See Fig Scraper BAR See Fig Before Starting the EngineTo USE Drift Cutters See Fig Check Engine OIL Level See Fig To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has Frozen Maintenance Engine Cleaning To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See Fig To Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine Speed Other StorageFuel System Engine OIL Troubleshooting KEY Part Description Auger HousingScrapper BAR Auger Bearing Exploded 178675X008 Corner Bracket Clean OUT Tool Gearbox AssemblyBearing Impeller Pulley Auger Assembly 30 RH Auger Assembly 30 LHSkid Plate LH Skid Plate RH Plastic Washer 181160X479 Drift Cutter BAR POP Rivet Knob BlackChute Snow Shield Shield Retainer Strap Cable Assembly Adjustable LEVER/CABLE Rotator AssemblyRotator Head Rotator Pivot Bracket Repair Parts Snow Thrower Model PP291E30 Handles Loop Handle RH Loop Handle LHLower Tube Pivot Support Knob RED SpacerHandle Knob Washer 3/8 Carriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Repair Parts Snow Thrower Model PP291E30 Drive Drive Plate Assembly AssemblySpeed Selector Rubber Ring Axle Shaft Repair PartsRoll PIN 3/16 Sprocket Complete LCT Engine Cover AssemblyFrame 427963X428 Traction Belt Impeller BeltIdler ARM Bracket Idler Pulley Wheel Assembly LH Repair Parts Snow Thrower Model PP291E30 Wheels187833X421 187865X421 Repair Parts Snow Thrower Model PP291E30 BAG of Parts Safety Ignition KEY422663 DECAL, Danger Repair Parts Snow Thrower Model PP291E30 DecalsDECAL, DANGER, Deflector DECAL, Instruction Limited Warranty