LEVER/CABLE Rotator Assembly, Rotator Head | Poulan PP291E30

REPAIR PARTS SNOW THROWER - MODEL PP291E30 (96198003000)

CONTROL PANEL / DISCHARGE CHUTE

2

2

*3

1

*7

*6

	KEY	PART
	NO.	NO.	DESCRIPTION	*4
	1	428272	LEVER/CABLE ROTATOR ASSEMBLY	*4	01.09.010-A	*5
	1	428272	LEVER/CABLE ROTATOR ASSEMBLY		01.09.010-A	*5
	2	17501010	SCREW 10-24 X .625
	*3	420678	ROTATOR HEAD
	*4	405932	ROTATOR PIVOT BRACKET
	*5	420675	PULLEY PIVOT
	*6	428273	CABLE ASSEMBLY ADJUSTABLE
	*7	428310	CABLE ASSEMBLY HEAT SHIELD

NOTES:

1. ITEMS INDICATED WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY.

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

27

Image 27

Poulan PP291E30 LEVER/CABLE Rotator Assembly, Rotator Head, Rotator Pivot Bracket, Pulley Pivot, Cable Assembly Adjustable

Contents

Snow Thrower Model Number Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Install Auger Control ROD See Figs Install Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Know Your Snow Thrower Operation Recoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety Requirements To USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To USE Fuel SHUT-OFF Valve See Fig To Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Throw Snow See Fig Check Engine OIL Level See Fig Before Starting the EngineScraper BAR See Fig To USE Drift Cutters See Fig If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before Stopping Maintenance Engine Cleaning Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute Deflector To Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig Carburetor Engine OIL StorageOther Fuel System Troubleshooting Auger Bearing Auger HousingKEY Part Description Scrapper BAR Exploded Impeller Pulley Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Bearing Skid Plate RH Auger Assembly 30 LHAuger Assembly 30 RH Skid Plate LH Plastic Washer 181160X479 Drift Cutter BAR Shield Retainer Strap Knob BlackPOP Rivet Chute Snow Shield Rotator Pivot Bracket LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Head Repair Parts Snow Thrower Model PP291E30 Handles Pivot Support Loop Handle LHLoop Handle RH Lower Tube Washer 3/8 SpacerKnob RED Handle Knob Carriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Repair Parts Snow Thrower Model PP291E30 Drive Rubber Ring AssemblyDrive Plate Assembly Speed Selector Sprocket Repair PartsAxle Shaft Roll PIN 3/16 427963X428 Cover AssemblyComplete LCT Engine Frame Idler Pulley Impeller BeltTraction Belt Idler ARM Bracket 187865X421 Repair Parts Snow Thrower Model PP291E30 WheelsWheel Assembly LH 187833X421 Repair Parts Snow Thrower Model PP291E30 BAG of Parts Safety Ignition KEY422663 DECAL, Instruction Repair Parts Snow Thrower Model PP291E30 DecalsDECAL, Danger DECAL, DANGER, Deflector Limited Warranty