Manuals / Brands / Lawn and Garden / Tiller / Poulan / Lawn and Garden / Tiller

Poulan PPCRT55 INSERT CABLE CLIP (See Fig. 6), CONNECT SHIFT ROD (See Fig. 7), REMOVE TILLER FROM CRATE, CHECK TIRE PRESSURE, HANDLE HEIGHT

1 28

Download 28 pages, 1.14 Mb

6

ASSEMBLY

INSERT CABLE CLIP (See Fig. 6)

• Insert plastic cable clip into hole on the back of handle

column. Push cables into clip.

ATTACH THIS END

TO SHIFT LEVER

IN DI CA TOR

SHIFT ROD

FIG. 6

SHIFT

ROD

HAIRPIN

CLIP

SHIFT

LEVER

INDICATOR

FIG. 7

CABLE CLIP

CABLES

HANDLE

COLUMN

CONNECT SHIFT ROD (See Fig. 7)

• Inser t end of shift rod farthest from bend into hole of

shift lever in di ca tor.

• Insert hairpin clip through hole of shift rod to secure

with bend of clip on right side.

REMOVE TILLER FROM CRATE

• Adjust handle assemby to lowest position. Be sure lock

lever is tightened securely.

• Make sure shift lever indicator is in “N” (neutral) po si tion

(See Fig. 7)

• Tilt tiller forward by lifting handle. Separate cardboard

cover from leveling shield.

• Rotate tiller handle to the right and pull tiller out of

carton.

CHECK TIRE PRESSURE

The tires on your unit were overinﬂ ated at the factory for

shipping purposes. Correct and equal tire pressure is

important for best tilling performance.

• Reduce tire pressure to 20 PSI(1.4 kg/cm2)

HANDLE HEIGHT

• Handle height may be adjusted to better suit operator.

(See “TO ADJUST HANDLE HEIGHT” in the Service

and Adjustments section of this manual).

Contents

Main MODEL: PPCRT55 MAINTENANCE AND STORAGE - IMPORTANT - SAFETY RULES Safe Operation Practices for Walk-Behind Powered Ro ta ry Tillers TRAINING PREPARATION OPERATION WARNING TABLE OF CONTENTS PRODUCT SPECIFICATIONS TOOLS REQUIRED FOR ASSEMBLY OPERATORS POSITION (See Fig. 1) CONTENTS OF HARDWARE PACK UNPACKING CARTON (See Fig. 2) INSTALL HANDLE (See Figs. 3, 4, and 5) INSERT CABLE CLIP (See Fig. 6) CONNECT SHIFT ROD (See Fig. 7) REMOVE TILLER FROM CRATE CHECK TIRE PRESSURE HANDLE HEIGHT KNOW YOUR TILLER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER. MEETS ANSI SAFETY REQUIREMENTS TURNING HOW TO USE YOUR TILLER STOPPING (See Fig. 9) TINE OPERATION - WITH WHEEL DRIVE FORWARD - WHEELS ONLY/TINES STOPPED REVERSE - WHEELS ONLY/TINES STOPPED BEFORE START ING ENGINE CHECK ENGINE OIL LEVEL (See Fig. 12) ADD GASOLINE OUTER SIDE SHIELDS (See Fig. 11) TO TRANSPORT CULTIVATING TILLING HINTS TINE SHEAR PINS GENERAL RECOMMENDATIONS LUBRICATION CHART BEFORE EACH USE LUBRICATION MAINTENANCE SCHEDULE LUBRICATION AIR FILTER (See Fig. 18) MUFFLER SPARK PLUG TRANSMISSION CLEANING COOLING SYSTEM (See Fig. 19) TILLER TO ADJUST HANDLE HEIGHT (See Fig. 20) TIRE CARE TO REMOVE WHEEL (See Fig. 21) TO REMOVE BELT GUARD (See Fig. 22) TO REPLACE GROUND DRIVE BELT (See Figs. 22 and 23) GROUND DRIVE BELT ADJUSTMENT (See Fig. 23) TINE REPLACEMENT (See Figs. 24, 25, and 26) TO ADJUST THROTTLE CONTROL CABLE (See Fig. 27) TO AD JUST CARBURETOR STORAGE ENGINE OIL CYLINDER(S) OTHER TILLER TROUBLESHOOTING POINTS TILLER - - MODEL NUMBER PPCRT55 (96091001200), PRODUCT NUMBER 960 91 00-12 HANDLE ASSEMBLY MAINFRAME, LEFT SIDE MAINFRAME, RIGHT SIDE TRANSMISSION TINE SHIELD TINE ASSEMBLY DECALS LIMITED WARRANTY PARTS AND SERVICE NOTE: