Tractor

CUSTOMER RESPONSIBILITIES

Always observe safety rules when performing any mainte- nance.

TRAILING EDGE UP

BLADE

MANDREL ASSEMBLY

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

FLAT WASHER

LOCK WASHER

CENTER

HOLE

STAR

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 11)

•Raise mower to highest position to allow access to blades.

•Remove hex bolt, lock washer and flat washer securing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble hex bolt, lock washer and flat washer in exact order as shown.

•Tighten bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.

HEX BOLT (GRADE 8)*

*A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

FIG. 11

TO SHARPEN BLADE (See Fig. 12)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and even- tual damage to mower and engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with bal- ancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

	CENTER HOLE
5/8" BOLT	BLADE
OR PIN

FIG. 12

BATTERY

Your tractor has a battery charging system which is suffi- cient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

PPR2042STA specifications

The Poulan PPR2042STA is a notable addition to Poulan’s lineup of outdoor lawn care equipment, specifically designed for those who require efficient and reliable grass cutting. This model stands out due to its powerful performance, user-friendly design, and advanced features that cater to both amateur gardeners and professional landscapers alike.

One of the main features of the PPR2042STA is its robust 42-inch cutting deck. This wide deck allows for efficient mowing of larger lawns without the need for excessive back-and-forth passes, thus reducing mowing time significantly. The deck is equipped with three high-performance blades, ensuring a clean and precise cut every time. With a cutting height adjustment feature, users can easily switch between different grass lengths, adapting to varying lawn conditions.

The PPR2042STA is powered by a 17.5 HP Briggs & Stratton engine, known for its reliability and performance. This engine delivers ample power to tackle thick grass and uneven terrains, making it suitable for diverse landscaping tasks. The automatic drive allows for a smooth operation, enabling users to navigate their lawns without the hassle of manual gear shifting.

Another standout technology integrated into the Poulan PPR2042STA is its innovative air induction mowing system. This system lifts the grass as it is cut, ensuring an even and consistent lawn appearance. Moreover, the mower’s design ensures effective grass discharge, whether utilizing the side discharge feature or connecting a mulching kit for finer grass clippings.

In terms of user comfort, the PPR2042STA boasts an ergonomic steering wheel and adjustable seat that ensures a comfortable ride, even during extended mowing sessions. The compact design of the mower, combined with its responsive controls, enhances maneuverability, making it easy to operate around flower beds, trees, and other obstacles.

Finally, the Poulan PPR2042STA features a durable steel frame that promises longevity, backed by a manufacturer's warranty that provides peace of mind to users. Maintenance is straightforward, with easy access to the engine and mower deck for cleaning and servicing.

With its powerful engine, efficient cutting system, and user-friendly design, the Poulan PPR2042STA represents excellent value for anyone looking to maintain their lawn effectively.

Poulan PPR2042STA owner manual Tractor

Models: PPR2042STA