Manuals / Poulan / Lawn and Garden / Tiller

Poulan PRRT9000 Service And Adjustments, Tiller, TO ADJUST HANDLE HEIGHT See Fig, Tire Care

Models: PRRT9000

1 20

Download 20 pages 31.8 Kb

Page 14

SERVICE AND ADJUSTMENTS

SERVICE AND ADJUSTMENTS

CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug.

TILLER

TO ADJUST HANDLE HEIGHT (See Fig. 19)

Select handle height best suited for your tilling conditions. Handle height will be different when tiller digs into soil.

•First loosen handle lock lever.

•Handle can be positioned at different settings between “HIGH” and “LOW” positions.

•Retighten handle lock lever securely after adjusting.

HANDLE

(HIGH POSITION)

HANDLE LOCK

LEVER

HANDLE

(LOW POSITION)

Fig. 19

TIRE CARE

CAUTION: When mounting tires, un- less beads are seated, overinflation can cause an explosion.

•Maintain 20 pounds of tire pressure. If tire pressures are not equal, tiller will pull to one side.

•Keep tires free of gasoline or oil which can damage rubber.

TO REMOVE WHEEL (See Fig. 20)

•Place blocks under transmission to keep tiller from tipping.

•Remove hairpin clip and clevis pin from wheel.

•Remove wheel and tire.

•Repair tire and reassemble.

CLEVIS PIN

HAIRPIN CLIP

Fig. 20

TO REMOVE BELT GUARD (See Fig. 21)

NOTE: For ease of removal, remove hairpin clip and clevis pin from left wheel. Pull wheel out from tiller about 1 inch.

•Remove two (2) screws from side of belt guard.

•Remove hex nut and washer from bottom of belt guard (located behind wheel).

•Pull belt guard out and away from unit.

•Replace belt guard by reversing above procedure.

BELT GUARD	SCREW
	AND WASHER	HEX NUT
		HEX NUT
		AND WASHER
		(LOCATED
		BEHIND
		TIRE)

	SCREW
	AND	HAIRPIN CLIP AND
	WASHER	HAIRPIN CLIP AND
	WASHER	CLEVIS PIN
		CLEVIS PIN

Fig. 21

14

Image 14

Poulan PRRT9000 Service And Adjustments, Tiller, TO ADJUST HANDLE HEIGHT See Fig, Tire Care, TO REMOVE WHEEL See Fig

Contents

REAR TINE TILLER OPERATORS MANUAL MODELIMPORTANT MANUAL ALWAYS WEAR EYE PROTECTION DURING OPERATIONMAINTENANCE AND STORAGE SAFETY RULESSafe Operation Practices for Walk-Behind Powered Rotary Tillers TRAININGCUSTOMER RESPONSIBILITIES TABLE OF CONTENTSPRODUCT SPECIFICATIONS 11-13CONTENTS OF HARDWARE PACK ASSEMBLYTOOLS REQUIRED FOR ASSEMBLY OPERATOR’S POSITION See FigUNPACKING CARTON See Fig INSTALL HANDLE See Figs. 3, 4, andstaples when handling or disposing of Be careful of exposedCHECK TIRE PRESSURE CONNECT SHIFT ROD See FigREMOVE TILLER FROM CRATE HANDLE HEIGHTOPERATION READ THIS MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLERMEETS ANSI SAFETY REQUIREMENTS KNOW YOUR TILLERTINE OPERATION - WITH WHEEL DRIVE HOW TO USE YOUR TILLERSTOPPING See Fig FORWARD - WHEELS ONLY/TINES STOPPEDTO TRANSPORT GAGED” position when starting engineBEFORE STARTING ENGINE CHECK ENGINE OIL LEVEL See Fig.11TILLING HINTS TINE SHEAR PINSCULTIVATING OPERATIONLUBRICATION CHART MAINTENANCEMAINTENANCE SCHEDULE GENERAL RECOMMENDATIONSDo not touch hot muffler or cylinder fins as contact may cause burns AIR CLEANER See FigENGINE TO CHANGE ENGINE OIL See Figs. 15 andMUFFLER CLEANINGCOOLING SYSTEM See Fig SPARK PLUGTILLER SERVICE AND ADJUSTMENTSTO ADJUST HANDLE HEIGHT See Fig TIRE CARESERVICE AND ADJUSTMENTS GROUND DRIVE BELT ADJUSTMENT See FigTO REPLACE GROUND DRIVE BELT See Fig. 21 and TINE REPLACEMENT See Figs. 23, 24 and SERVICE AND ADJUSTMENTSENGINE TO ADJUST CARBURETORSERVICE AND ADJUSTMENTS FUEL SYSTEM STORAGEOTHER ENGINE OILTROUBLESHOOTING POINTS LIMITED WARRANTY Mississauga, Ontario