Poulan TE 500 CXL manual Cutting Safety, Transporting and Storage, Attaching the Handle

SDo not smoke or allow smoking near fuel or the unit.

S Avoid spilling fuel or oil. Wipe up all fuel spills.

SMove at least 10 feet (3 meters) away from

fueling site before starting engine.

S Stop engine and allow to cool before re- moving fuel cap.

S Always store gasoline in a container ap- proved for flammable liquids.

CUTTING SAFETY

WARNING: Inspect the area before each use. Remove objects (rocks, broken glass, nails, wire, etc.) which can be thrown by or become entangled in line. Hard objects can damage the trimmer head and be thrown causing serious injury.

SUse only for trimming, mowing, edging and

sweeping. Do not use for pruning or hedge trimming.

SKeep firm footing and balance. Do not over- reach.

SKeep all parts of your body away from muf- fler and spinning line. Keep engine below

waist level. A hot muffler can cause serious burns.

SCutting with the line on left side of the shield will throw debris away from the operator.

SUse only in daylight or good artificial light.

TRANSPORTING AND STORAGE

S Allow the engine to cool; secure unit before storing or transporting in vehicle.

S Empty fuel tank before storing or transport- ing the unit. Use up fuel left in the carburetor by starting engine and letting it run until it stops.

S Store unit and fuel in an area where fuel va- pors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

S Store unit so line limiter blade cannot acci- dentally cause injury. Unit can be hung by the tube.

S Store the unit out of the reach of children.

SAFETY NOTICE: Exposure to vibrations through prolonged use of gasoline powered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or ab- normal swellings. Prolonged use in cold weather has been linked to blood vessel dam- age in otherwise healthy people. If symptoms occur such as numbness, pain, loss of strength, change in skin color or texture, or loss of feeling in the fingers, hands, or joints, discontinue the use of this tool and seek med- ical attention. An anti--vibration system does not guarantee the avoidance of these prob- lems. Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condi- tion of this tool.

SPECIAL NOTICE: This unit is equipped with a temperature limiting muffler and spark arresting screen which meets the require- ments of California Codes 4442 and 4443. All U.S. forest land and the states of California, Idaho, Maine, Minnesota, New Jersey, Ore- gon, and Washington require by law that many internal combustion engines be equipped with a spark arresting screen. If you operate in a locale where such regulations ex- ist, you are legally responsible for maintaining the operating condition of these parts. Failure to do so is a violation of the law. For normal homeowner use, the muffler and spark arrest- ing screen will not require any service. After 50 hours of use, we recommend that your muffler be serviced or replaced by your Au- thorized Service Dealer.

WARNING: Make sure unit is proper- ly assembled and all fasteners are secure.

ATTACHING THE HANDLE

Groove

S Assemble handle to the unit as shown; make sure bottom of handle is seated in the groove in the trigger housing.

NOTE: Adjustment knob must be as- sembled on the side of the unit opposite the operator ’s position.

S Pivot handle to a comfortable position. Tighten handle securely.

ATTACHING THE SHIELD

WARNING: The shield must be prop- erly installed. The shield provides partial protection from the risk of thrown objects to the operator and others and is equipped with a line limiter which cuts excess line. The line limiter (on underside of shield) is sharp and can cut you.

SRemove wing nut from shield.

SInsert bracket into slot on shield.

SPivot shield until bolt passes through hole in bracket.

S	Securely tighten wing nut.
	Bracket
	Slot

Shield Wing Nut

3