Powermate VTE4000 important safety instructions Bad Cell Detection, Specifications

AA/AAA Battery Charger Owner’s Manual

Model No.: VTE4000

30 minutes--Worldwide Use--U-Smart Charger

Your AA/AAA Battery Charger is designed to charge Vapex’Tech NiMH rechargeable REGULAR batteries rated to 2700mAh(AA) or 1000mAh (AAA). The batteries will be fully-charged by Microprocessor-Control System in 30 MINUTES for AA/AAA batteries. You can change 1/2/3/4 AA/AAA NiMH batteries simultaneously.

This charger is designed to charge Nickel-Metal- Hydride AA,

AAAsize rechargeable batteries. Please note that this charger must not be used for Alkaline, Carbon Zinc, Lithium or any kind of battery other than Nickel Metal Hydride.

SAVE THESE INSTRUCTIONS

CHARGER FEATURES INCLUDE:

zRecharges 1 piece to 4 pieces of AA & AAA Ni-MH batteries at a time.

zPowered by the supplied AC Adaptor when

using at home or by the supplied DC Car Adaptor when using in a vehicle.

zBS(UK) & VDE(EU) interchangeable plugs can be added on the US plug

zMicroprocessor Controlled – Batteries life well protected by –dV detection and timer protection.

zAutomatic charging current selection for size AA and AAA.

zLED display for rapid charge/trickle charge/bad cell detection

Red LED – rapid charge ; Green LED – trickle charge ;

Flashing Red LED – Cells are not suitable for charging i.e. Short circuit or wrong polarity.

Safety features :

z-dV cut-off function

zSafety timer to prevent over charge

zThermal cut off

zReverse-polarity protection

zBad cell Detection

OPERATION INSTRUCTIONS : -

1.Insert 1 to 4 pieces of AA/AAA rechargeable Ni-MH batteries into the battery compartment.

2.Make correct contact for polarity ( + and – ) ; according to the sign in the battery compartment.

3.When using at home

Connect the supplied AC adaptor ‘s barrel plug into the jack on the back of the charger. Plug the AC adaptor into any available 100-240VAC outlet. The switching power supply will adjust automatically, when using overseas a plug adaptor may be required.

Caution: The supplied AC adaptor supplies 12VDC and delivers 3.3A, and its plug fits into the charger’s DC input jack. Using an adaptor that does not meet these specifications could damage the charger or the adaptor.

When using in a vehicle

Connect the supplied DC car adaptor’s barrel plug into the charger’s DC input jack. Plug the large end of the cord into the 12V car lighter power port.

4.The Red LED will glow to indicate the proper charging. After the batteries are fully charged, the red LED will turn off and the green LED will light up indicating the trickle charge is on. The charged batteries are ready for use.

5.Unplug the charger and remove the batteries from the charger when not in use.

6.Begin against step 1 to charge the next set of batteries.

Bad Cell Detection:

When charge process is started, the charger detects the health status of each of the cells in the battery compartment. If any battery is unsuitable for charging the status LED will flash.

Charging time :

Size	Charging	Nickel Metal Hydride
AA	current	2000mAh	30 minutes
AA		2100mAh	32 minutes
AA	4A	2200mAh	33 minutes
AA		2300mAh	35 minutes
AA		2400mAh	36 minutes
AA		2500mAh	38 minutes
AA		2700mAh	41 minutes
AAA		650mAh	25 minutes
AAA	1.7A	750mAh	29 minutes
AAA		850mAh	32 minutes
AAA		900mAh	34 minutes
AAA		1000mAh	38 minutes

*Charge time will vary depending upon the brand, capacity and condition of batteries being charged.

Specifications:

Power supply : 100-240VAC, 50/60 Hz

International Compatible

Charge rate : AA size - 4A

AAA size – 1.7A

Important Safety Instructions

1.Before charging, read instruction.

2.This power unit is intended to be correctly orientated in a vertical or floor mount position

3.This charger is intended for use with Nickel-metal-hydride rechargeable batteries only. Attempting to charge other types of batteries may cause personal injury and damage to the charger.

4.Do not expose charger to rain or moisture. For indoor use only.

5.Remove from mains when not in use.

6.Never use an extension cord or any attachment not recommended by manufacturer, otherwise this may result in a risk of fire, electric shock or injury to persons.

7.Do not operate the charger if it has been subjected to shock or damage. Take it to a qualified serviceman for repair.

8.Do not disassemble the charger. Incorrect reassemble may result in a risk of electric shock or fire.

9.Unplug the charger from outlet before attempting any maintenance of cleaning.

10.The appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure that they do not play with the appliance.

11.Before scrapping your charger, remove the batteries from the unit and they are disposed of safety.