![](/images/new-backgrounds/1202342/2023423x1.webp)
77 | 88 | 99 |
700VA model (12V- 7AH battery)
11 | 22 | 33 |
|
|
|
|
|
44 | 55 | 66 |
|
|
|
|
|
|
|
|
|
|
|
|
|
77 | 88 | 99 |
|
|
|
|
|
|
|
|
|
|
|
|
|
STATUS INDICATORS:
The UPS provides both visual and audible status indicators. Visual indicators consist of two LEDs to represent the following conditions:
On utility power operation
On battery power operation
UPS fault/alarm
LED & Alarm Status Table
UPS Status | Green LED | Red LED | Buzzer | ||
| Blink 1(by turns) | B1 | |||
AC | Charging | ON | X | X | |
(Utility) |
|
|
|
| |
Charge Off | ON | X | X | ||
Mode |
|
|
|
| |
Low Battery | ON | Blink 2 | B2 | ||
| |||||
| Over Load | ON | Blink 2 | B4 |
DC | Normal | Blink 2 | X | B1 | |
(Battery) | Over Load | Blink 2 | Blink 2 | B4 | |
Mode |
|
|
|
| |
Low Battery | Blink 2 | Blink 2 | B3 | ||
| |||||
Short / Fault | X | ON | ON | ||
X | Blink 2 | B5 |
Notes:
Blink 1: ON 0.5 seconds / OFF 0.5 seconds.
Blink 2: ON 0.25 seconds / OFF 0.25 seconds.
B1: 1 beep / 5 seconds, ON 0.25 seconds / OFF 4.75 seconds.
B2: 3 beeps / 30 seconds, ON 0.25 seconds / OFF 0.25 seconds 3 times, 28.5 seconds OFF.
B3: 2 beeps / 5 seconds, ON, 0.25 seconds / OFF 0.25 seconds 2 times, 4 seconds OFF.
B4: ON 0.5 seconds / OFF 0.5 seconds.
B5: 3 beeps / 5 seconds, ON 0.25 seconds / OFF 0.25 seconds 3 times, 3.5 seconds OFF.
SPECIFICATIONS
Model Numbers | Capacity | |
PW3105 350A | 350 VA / 210W | |
PW3105 500A | 500 VA / 300W | |
PW3105 700A | 700 VA / 420W | |
Nominal Input Voltage | 240Vac | |
Nominal Output Voltage | 240Vac | |
Frequency | 50 / 60 Hz auto sensing | |
|
| |
Total 6 Outlets | 3 Battery Backup & Surge Protection | |
3 Surge Protection only | ||
| ||
Lighting / Surge Protection | 476 Joules | |
Transfer Time to Battery/AC | 6ms Typical | |
|
| |
Battery Type | Maintenance free, Sealed and leak proof | |
battery | ||
| ||
Battery Specification | 350 / 500 VA: 12V 5 AH | |
750 VA: 12V 7 AH | ||
| ||
|
| |
Typical Backup Time | 3 minutes minimum at full rated load | |
Internet / Phone / Fax Protection | RJ11 | |
Short Circuit Protection | Circuit Breaker | |
Communication Port | USB | |
Operating Temperature | 0 C to 40 C | |
Operating Relative Humidity | 0 to 95% | |
|
| |
Storage Temperature | ||
Net Weight | 350VA - 4.8 kg | |
500VA - 5.5 kg | ||
| ||
| 700VA - 7 kg | |
Dimensions (W x D x H) | 280 x180 x115mm |
*Due to continuing product improvement programs, specifications subject to change without notice.
TROUBLESHOOTING
Symptom | Possible Cause | Action to Take |
UPS will not turn on | The battery is disconnected | Connect the battery (see Connect |
| or utility power is not | Battery) and ensure power is |
| available at the wall outlet. | available at the wall outlet. |
| Input Circuit Breaker has | Reduce the amount of equipment |
| tripped. | plugged into the outlets of the UPS. |
|
| Next, reset the circuit breaker by |
|
| pushing the plunger back in. |
|
|
|
UPS is making a | The “Battery Backup & | Turn off the UPS and reduce the |
continuous sound and | Surge Protection” outlets | amount of equipment connected to |
the “Overload” indicator | are overloaded. | these outlets. |
is lighted. |
|
|
UPS does not provide | The battery is not fully | Removed all connected equipments |
expected runtime. | charged. | from the UPS and charge the battery |
|
| at least 8 hours. During this charging |
|
| period, turn off the UPS to prevent |
|
| unnecessary discharging. |
| Battery is getting older. | Call for service or you can replace |
|
| the battery by ordering one from |
|
| your dealer. |
When utility power fails, | The UPS is overloaded. | Reduce the amount of equipment |
connected equipment |
| plugged into the outlets of the UPS. |
| Try reducing the load by removing | |
loses power |
| |
| one piece of equipment at a time to | |
|
| |
|
| determine if the problem continues. |
| The UPS has exhausted | The UPS will turn off when the |
| its available run time. | battery has been depleted during |
|
| an extended power outage. Allow |
|
| the UPS to |
|
| before continuing on battery opera |
|
| tion. |
| Equipment is connected | Ensure the equipment that is to be |
| to the “surge Protection” | protected from a power outage is |
| outlets. | plugged into the “Battery Backup & |
|
| Surge Protection” outlets. |
| The UPS may require | Contact Powerware Technical |
| service. | Support |
SERVICE AND SUPPORT
For service and support please call your local distributor or the Powerware Australia National Service and Repair Centre.
Australia freecall | 1300 303 059. |
Please have the following information ready:
Model number and serial number
Symptoms of failure or problem
Customer contact information
For additional information and to register your warranty, please visit
www.powerware.com.au
Register your warranty within 30 days and receive an extended
Eaton Power Quality Pty Ltd
North Ryde NSW 2113
MA6B412005(2005/01/12)