HOW TO TURN ON THE POWER

IMPORTANT: If the treadmill has been exposed to cold temperatures, allow it to warm to room tem- perature before turning on the power. If you do not do this, the console displays or other electrical components may become damaged.

Plug in the power cord (see

 

 

 

 

 

 

 

 

 

 

page 11). Next, locate the

 

 

 

 

 

reset/off circuit breaker on

 

 

 

 

 

 

Reset

 

 

 

 

the treadmill frame near the

 

Position

 

 

 

power cord. Switch the cir-

 

 

 

 

 

 

 

 

 

 

cuit breaker to the reset po-

 

 

 

 

 

 

 

 

 

 

sition.

 

 

 

 

 

IMPORTANT: The console features a display demo mode, designed to be used if the treadmill is dis- played in a store. If the displays light as soon as you plug in the power cord and switch the circuit breaker to the reset position, the demo mode is turned on. To turn off the demo mode, hold down the Stop button for a few seconds. If the displays remain lit, see THE INFORMATION MODE on page 16 to turn off the demo mode.

Next, stand on the foot rails of the treadmill. Find the clip attached to the key (see the drawing on page 12) and slide the clip onto the waistband of your clothes.

Then, insert the key into the console. After a moment, the displays will light. IMPORTANT: In an emergency situation, the key can be pulled from the console, causing the walking belt to slow to a stop. Test the clip by carefully taking a few steps backward; if the key is not pulled from the console, adjust the posi- tion of the clip.

HOW TO USE THE MANUAL MODE

1.Insert the key into the console.

See HOW TO TURN ON THE POWER above.

2.Select the manual mode.

When the key is in- serted, the manual mode will be selected and a track will appear in the matrix. If a preset workout has been selected, remove the key and then reinsert it.

3.Start the walking belt.

To start the walking belt, press the Start button, the Go button, the speed increase button, or one of the speed buttons numbered 2 through 10.

If the Start button, the Go button, or the speed in- crease button is pressed, the walking belt will begin to move at 1 mph. As you exercise, change the speed of the walking belt as desired by pressing the speed increase and decrease buttons. Each time a button is pressed, the speed setting will change by 0.1 mph; if a button is held down, the speed setting will change in increments of 0.5 mph. Note: After the buttons are pressed, it may take a moment for the walking belt to reach the selected speed setting.

If one of the numbered speed buttons is pressed, the walking belt will gradually increase in speed until it reaches the selected speed setting.

To stop the walking belt, press the Stop button. To restart the walking belt, press the Start button, the Go button, the speed increase button, or one of the speed buttons numbered 2 through 10.

4.Change the incline of the treadmill as desired.

To change the incline of

the treadmill, press the Incline increase and de- crease buttons or one of

the numbered incline but- tons. Each time you

press the incline increase or decrease button, the incline will change by 0.5%. If you press one of the numbered incline buttons, the treadmill will adjust to the selected incline setting. Note: After you press the buttons, it may take a moment for the treadmill to reach the selected incline setting.

5.Monitor your progress with the matrix and the displays.

The matrix—When the

manual mode is se- lected, the matrix will dis- play a 1/4-mile track. As you exercise, the indica- tors around the track will

light in succession until

the entire track is lit. The track will then darken and the indicators will again begin to light in succes- sion.

13

Page 13
Image 13
ProForm 831.24745.2 user manual HOW to Turn on the Power, HOW to USE the Manual Mode