Assembly

Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Refer to the drawings below to identify the parts

used in assembly. Assembly requires the following tools: The allen wrench				included and your own
phillips screwdriver		, mallet	wire cutters	and needle-nose
pliers	.

Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Long Screw (79)–4

Screw (101)–4

Handrail Bolt (89)–4

Handrail Washer (29)–4

1.With the help of a second person, carefully raise the Uprights (82) until the treadmill is in the position shown.

Insert one of the Extension Legs (103) into the treadmill as shown. Make sure that the Thick Base Pad (97) is on the indicated side. Note: It may be helpful to tip the Uprights (82) in the direction shown by the arrow as you insert the Extension Leg. To fully insert the Extension Leg, it may be necessary to tap it with a mallet.

Insert the other Extension Leg (103) in the same way.

2.Refer to drawing 2a. If there are plastic ties in the Cage Nuts (36) in the Right Handrail (85), remove the plastic ties. Pull 5 to 6” of the Wire Harness (17) out of the Right Upright (82). Route the Wire Harness through the bracket on the Right Handrail and out of the indicated hole. If nec- essary, use needle-nose pliers to grip the connectors on the Wire Harness. Thread the included wire tie through the indicated hole in the Right Handrail (85).

Refer to drawing 2b. Look into the Right Handrail (85) and make sure that the Wire Harness (17) has been se- cured to the side shown. Tighten the wire tie and cut off the excess from the end.

Refer to drawing 2c. Insert the bracket on the Right Handrail (85) into the upper end of the right Upright (82). Hand Tighten a Handrail Bolt (89) with a Handrail Washer (29) into each side of the Upright as shown.

Attach the Left Handrail (23) as described above. Note: There is not a wire in the left Upright (82).

1
			82
					82
				97	103
2a		2c		17
85		23		17
85
	17		89		89
Tie	36	85	89		29
		85		29


82			82
2b	Tie
85
	17
					103

ProForm 831.299520 Assembly, Phillips screwdriver Mallet Wire cutters Needle-nose Pliers

Models: 831.299520

ASSEMBLY

phillips screwdriver

, mallet

wire cutters

and needle-nose

pliers

1
			82
					82
				97	103
2a		2c		17
85		23		17
85
	17		89		89
Tie	36	85	89		29
		85		29


82			82
2b	Tie
85
	17
					103

1
			82
					82
				97	103
2a		2c		17
85		23		17
85
	17		89		89
Tie	36	85	89		29
		85		29


82			82
2b	Tie
85
	17
					103

1
			82
					82
				97	103
2a		2c		17
85		23		17
85
	17		89		89
Tie	36	85	89		29
		85		29


82			82
2b	Tie
85
	17
					103