PART | R0402A |
To locate the parts listed below, refer to the EXPLODED DRAWING attached in the center of this manual.
Key |
|
| Key |
|
| Key |
|
|
No. | Qty. | Description | No. | Qty. | Description | No. | Qty. | Description |
1 | 1 | Motor Belt | 49 | 2 | Belt Guide | 99 | 1 | Grommet |
2 | 1 | Pulley/Flywheel/Fan | 50 | 1 | Book Holder | 100 | 1 | Allen Wrench |
3 | 4 | Motor Nut | 51 | 1 | Front Belly Pan | 101 | 21 | Screw |
4* | 1 | Motor/Pulley/ | 52 | 1 | Power Supply | 102 | 1 | Audio Wire Nut |
|
| Flywheel/Fan | 53 | 4 | Cable Tie Clamp | 103 | 2 | Extension Leg |
5 | 1 | Incline Motor Bolt | 54 | 4 | Cable Tie | 104 | 2 | Base Endcap |
6 | 1 | Optic Switch | 55 | 1 | Walking Belt | 105 | 1 | Shock |
7 | 1 | Incline Motor | 56 | 1 | Latch Spacer | 106 | 1 | Choke |
8 | 2 | Incline Motor Spacer | 57 | 1 | Rear Roller | 107 | 2 | Pulse Bar Bolt |
9* | 1 | Latch Assembly | 58 | 1 | Belly Pan Spacer | 108 | 2 | Pulse Bar Washer |
10 | 1 | Small Plate | 59 | 2 | Rear Foot | 109 | 1 | Pulse Bar |
11 | 1 | Rear Foot Spacer | 60 | 4 | Rear Foot Screw | 110 | 1 | Left Foam Grip |
12 | 1 | Frame | 61 | 1 | Ground Wire | 111 | 1 | Trim Guard |
13 | 1 | Hand Pulse Wire | 62 | 27 | 1/2” Screw | 112 | 1 | Shield |
14 | 1 | Incline Motor Pivot Bolt | 63 | 1 | Belly Pan | 113 | 2 | Static Decal |
15 | 6 | Incline Motor Nut | 64 | 1 | Rear Endcap | 114* | 2 | Extension Leg |
16 | 4 | Guide Screw | 65 | 2 | Rear Roller Adj. Bolt |
|
| Assembly |
17 | 4 | Plastic | 66 | 1 | Motor | 115 | 2 | Incline Pivot Nut |
18 | 2 | Hood Bracket (short) | 67 | 1 | Latch Decal | 116 | 1 | Console Base Bottom |
19 | 1 | Hood Bracket (long) | 68 | 4 | Platform Screw | 117 | 2 | Upright Endcap |
20 | 2 | Warning Decal | 69 | 1 | Incline Motor Plate | 118 | 1 | Optic Switch Nut |
21 | 1 | Reed Switch | 70 | 1 | Catch | 119 | 2 | Base Pad |
22 | 1 | Reed Switch Clip | 71 | 1 | Walking Platform | 120 | 2 | Rear Isolator |
23 | 1 | Motor/Controller Wire | 72 | 5 | 8” Cable Tie | 121 | 1 | Frame Guide |
24 | 1 | Controller | 73 | 1 | Jack | 122 | 2 | Frame Guide Screw |
25 | 1 | Electronics Bracket | 74 | 1 | Motor Tension Bolt | 123 | 2 | Interface Bracket |
26 | 1 | Circuit Breaker | 75 | 2 | Foot Rail Insert | # | 1 | 8” White Wire, M/F |
27 | 1 | Power Cord | 76 | 9 | Small Screw | # | 1 | 14” White Wire, 2F |
28 | 1 | Power Cord Grommet | 77 | 1 | Console | # | 1 | 14” Blue Wire, 2F |
29 | 1 | On/Off Switch | 78 | 2 | Ground/Switch Washer | # | 1 | 4” Blue Wire, 2F |
30 | 14 | Hood Bracket Screw/ | 79 | 4 | Long Screw | # | 1 | 4” Black Wire, 2F |
|
| Incline Shield Screw | 80 | 1 | iFIT.com Wire | # | 1 | 4” Green Wire, F/Ring |
31 | 1 | Incline Base | 81 | 4 | Motor Star Washer | # | 1 | 8” Green Wire, 2 Ring |
32 | 2 | Frame Pivot Bolt | 82 | 1 | Upright | # | 1 | 4” Red Wire, M/F |
33 | 2 | Frame Pivot Spacer | 83 | 2 | Incline Base Pivot Bolt | # | 1 | 20” Wire Harness |
34 | 1 | Upright Wire Harness | 84 | 1 | Optic Switch Bolt | # | 1 | 25” Wire Harness |
35 | 1 | Front Roller Adj. Bolt | 85 | 2 | Handrail Extension | # | 1 | User's Manual |
36 | 3 | Roller Adj. Washer | 86 | 2 | Wheel Bolt |
|
|
|
37 | 2 | Motor Tension Nut | 87 | 1 | Console Base | # These parts are not illustrated | ||
38 | 4 | Motor Bolt | 88 | 1 | Motor Tension Washer | |||
39 | 2 | Cap Screw | 89 | 1 | Incline Stop Bracket | * Includes all parts shown in the box | ||
40 | 1 | Left Foot Rail Cap | 90 | 1 | Key/Clip | **For more information about the op- | ||
41 | 2 | Foot Rail | 91 | 1 | Optic Disk | tional chest pulse sensor or hand | ||
42 | 1 | Front Roller/Pulley | 92 | 1 | Right Foot Rail Cap | weights, see page 19. For informa- | ||
43 | 1 | Magnet | 93 | 1 | Motor Tension Bushing | tion about iFIT.com CDs or video- | ||
44 | 4 | Platform Screw (mid) | 94 | 1 | Motor Hood | cassettes, call | ||
45 | 4 | Isolator | 95 | 2 | Front Wheel |
|
|
|
46 | 7 | Isolator Screw | 96 | 1 | Incline Motor Shield |
|
|
|
47 | 15 | Plastic Fastener | 97 | 4 | Thick Base Pad |
|
|
|
48 | 1 | Right Foam Grip | 98 | 1 | 12” Audio Wire |
|
|
|
26
