2.While another person lifts the back of the Frame (1), attach the Rear Stabilizer (9) to the Frame with two
M10 x 75mm Carriage Bolts (34) and two M10 Nylon Locknuts (33).
3.The Console (23) requires three “AA” batteries (not included); alkaline batteries are recommended. Insert
three batteries into the battery compartment. | Make |
sure that the batteries are oriented as shown by |
|
the diagram inside the battery compartment. |
|
4.While another person holds the Console (23) in the position shown, insert the control cable and the con- sole wire down through the Upright (2). Attach the ground wire to the Upright with an M4 x 16mm Self- tapping Screw (52). Insert the excess cable and wire into the Upright.
Attach the Console (23) to the Upright (2) with four
Console Screws (59). Be careful to avoid pinching the cable and wires.
Make sure the Resistance Knob (42) is set on the lowest setting before proceeding to the next step.
5.While another person holds the Upright (2) in the posi- tion shown, connect the console wire to the Reed
Switch Wire (53).
Next, connect the control cable to the Resistance
Cable (43) in the following way:
•Refer to drawing A. Pull up on the metal bracket, and insert the tip of the control cable into the wire clip on the Resistance Cable (43) as shown.
• Refer to drawing B. Firmly pull the control cable and slide it into the metal bracket on the Resistance
Cable (43) as shown.
•Refer to drawing C. Using pliers, squeeze the prongs on the upper end of the metal bracket together.
Push the excess cable and wires down into the Frame |
| |
(1). Insert the Upright (2) into the Frame. | Do not pinch | |
the wires or cables. | Secure the Upright to the Frame | |
with two M10 x 74mm Bolts (7), two M10 Split |
| |
Washers (45), and two M10 Nylon Locknuts (33). | Do | |
not tighten the Bolts yet. |
|
|
6
2 |
|
| 33 |
|
|
|
|
| |
|
|
|
| 9 |
| 33 |
|
|
|
| 1 |
|
|
|
|
|
|
| 34 |
3 |
|
|
|
|
|
|
| Batteries | |
23 |
|
|
|
|
4 |
| 23 |
|
|
|
|
|
| 42 |
Console Wire |
|
|
| |
59 |
|
|
|
|
| 52 |
| Control Cable |
|
Ground Wire |
|
|
| |
|
| 59 |
| |
|
|
|
| |
| 2 |
|
|
|
5 | 2 |
| Make sure the | |
|
| |||
|
| 45 | Wires and | |
|
| Cables do | not | |
|
| 7 | ||
33 |
| get pinched | and | |
|
| damaged during | ||
|
|
| ||
Control |
|
| this step. | |
| Console |
|
| |
Cable |
|
|
| |
|
| Wire |
|
|
43 |
| 53 |
|
|
|
|
|
| |
1 |
|
|
|
|
A | B |
| C |
|
Metal |
|
| Control | |
Bracket |
|
| ||
|
| Cable | ||
|
|
| ||
Control | Control |
|
| |
| Cable |
|
| |
Cable |
|
|
| |
|
|
|
| |
43 |
| 43 |
| 43 |
