1.Identify the Front Stabilizer (3). While another person lifts the front of the Frame (1), attach the Front Stabilizer to the Frame with two M10 x 112mm Carriage Bolts (34) and two M10 Nylon Locknuts (29).
Make sure that the Front Stabilizer is turned so the Wheels (32) are not touching the floor.
2.While another person lifts the back of the Frame (1), attach the Rear Stabilizer (4) to the Frame with two M10 x 112mm Carriage Bolts (34) and two M10 Nylon Locknuts (29).
3.While another person holds the Upright (2) in the posi- tion shown, connect the Upper Wire Harness (86) to the Lower Wire Harness (87). Carefully pull the upper end of the Upper Wire Harness to remove any slack. While holding the upper end of the Upper Wire Harness, insert the Upright into the Frame (1). Do not pinch the Wire Harnesses.
Slide an M10 Split Washer (70) and a Frame Spacer
(83)onto an M10 x 88mm Button Bolt (63). Insert the Button Bolt into the Frame (1) and the Upright (2).
Make sure that the concave end of the Frame Spacer is turned toward the Frame. Do not tighten the Button Bolt yet.
Attach the Water Bottle Holder (91) to the Upright
(2) with two M4 x 22mm Screws (93).
4.While another person holds the Console (5) in the position shown, connect the wire harness on the Console to the Upper Wire Harness (86). Insert the excess wire harness into the Upright (2). Next, attach the Console to the Upright with four M4 x 16mm Screws (66). Be careful to avoid pinching the wire harnesses.
1 |
|
| 32 |
|
|
| 34 |
|
| ||
|
|
|
| ||
| 32 |
|
|
|
|
|
| 3 |
|
|
|
|
|
| 1 |
|
|
|
|
|
| 29 |
|
2 |
|
|
|
|
|
|
|
|
| 29 | 4 |
|
|
|
|
| |
|
| 29 |
|
|
|
|
| 1 |
|
| 34 |
|
|
|
|
| |
3 |
|
|
| Make sure the | |
|
|
|
| ||
|
|
|
| wire harnesses | |
|
|
|
| do not get | |
|
|
|
| pinched and | |
|
|
| 91 | damaged during | |
|
|
| this step. | ||
| 2 |
|
| ||
|
|
|
|
| |
|
|
|
| 93 |
|
| 63 | 70 | 86 |
|
|
|
|
|
| ||
|
| 87 |
|
| |
|
|
|
|
| |
|
|
|
| 1 |
|
|
| 83 |
|
|
|
4 |
|
|
| 5 |
|
|
| Wire |
|
| |
|
|
|
|
| |
| Harness |
|
|
| |
|
| 86 |
|
|
|
| 66 |
|
| Make sure the | |
|
| 2 | wire harnesses | ||
|
|
| |||
|
|
|
| do not get | |
|
| 66 |
| pinched and | |
|
|
| damaged during | ||
|
|
|
| ||
|
|
|
| this step. | |
6
