Proson RV-2300DTS ATT Lyssna PÅA Surroundljud, Att justera Dolby Pro Logic II inställningarna

SVENSKA

ATT LYSSNA PÅA SURROUNDLJUD

Surroundljudseffekten kommer inte att fungera riktigt om signalen passerar genom en grafisk equalizer.

Läs manualen till din equalizer för vägledning hur du stänger av ce on switching off (or defeating) the equalizer.

1	Välj rätt läge, beroende på vilken typ av insignal
	du använder.
	AUTO

eller AUTO

•Varje gång AUTO-knappen trycks ner byter avkodningsläget enligt följande:

IN-AUTO : The input digital signal format(DTS, Dolby Digital or PCM(2 channel stereo), etc.) used by the selected digital input source is detected automatically to perform the necessary decoding process for optimum surround modes.

IN-DTS : The DTS signal processing is performed only when DTS signals are input.

IN-PCM : The PCM signal processing is performed only when PCM signals are input.

Notes:

•Only when the digital input is selected as signal input for the input sources except TUNER, AUX and TAPE MONITOR, the decoding mode can be selected.

•Noise may be generated at the beginning of playback and while searching during DTS playback in the IN-AUTO mode. In this case, try playing in the IN-DTS mode.

Select the desired surround mode.

2 DSP MODE

or DSP MODE

•Each time the DSP MODE button is pressed, the surround mode changes depending on the input signal format and the selected decoding mode as follows:

When Dolby Digital signals are input in the IN-AUTO mode, one of the following modes can be selected depending on the number of the recorded channels.

•Dolby Digital 5.1-channel sources: DOLBY DIGITAL and DOLBY VIRTUAL.

•Dolby Digital 2-channel sources: DOLBY PRO LOGIC II MOVIE, DOLBY PRO LOGIC, DOLBY PRO LOGIC II MUSIC, DOLBY PRO LOGIC II MATRIX, DOLBY PRO LOGIC II CUSTOM and DOLBY VIRTUAL.

When PCM(2 channel stereo) signals are input in the IN-AUTO or IN-PCM mode, one of the following modes can be selected :

DOLBY PRO LOGIC II MOVIE, DOLBY PRO LOGIC, DOLBY PRO LOGIC II MUSIC, DOLBY PRO LOGIC II MATRIX, DOLBY PRO LOGIC II CUSTOM, DOLBY VIRTUAL, CHURCH, THEATER,HALL and STADIUM.

•When the analog input is selected as signal input and analog stereo signals are input, you can select the desired of these above surround modes, too.

•However, when DTS signals are input in the IN-AUTO or IN-DTS mode, the DTS mode will be selected regardless of using the DSP MODE button.

Notes:

•When the selected decoding mode is not matched to the input signal format, no sound is heard. Therefore, be sure to select the required decoding mode and the available surround mode according to the input signal format.

•When the 6 CH DIRECT is selected as an input source, the decoding and surround modes cannot be selected.

När du ska stänga av surroundläget och lyssna i stereo.

STEREO

eller STEREO

•Stereoläge är valt.

•För att stänga av stereoläget, välj önskat surroundläge med hjälp av DSP MODE-knappen.

Att justera Dolby Pro Logic II inställningarna

•When selecting the Dolby Pro Logic II Music and Custom modes, you can adjust the various surround parameters for optimum surround effect.

While scrolling “PL II MUSIC”(for Dolby Pro Logic II

3 Music mode) or “PL II CUSTOM”(for Dolby Pro Logic II Custom mode), press the MEMORY/ENTER button to select the desired parameter.

MEMO/ENTER

•Each time this button is pressed, the parameter changes and is displayed for 5 seconds as follows:

Panorama mode(“PANO”) : This mode extends the front stereo image to include the surround speakers for an exciting “wraparound”effect with side wall imaging. Select “OFF” or “ON”.

Center width control(“C-WID”) : This control adjusts the center image so it may be heard only from the center speaker, only from the left/right speakers as a phantom image, or from all three front speakers to varying degrees. The control can be set in 8 steps from 0 to 7. Dimension control(“DIMEN”) : This control gradually adjusts the soundfield either towards the front or towards the rear. The control can be set in 7 steps from - 4 to +2.

7 kHz Low Pass Filter(“ LPF”) : Select “OFF” or “ON” to turn off or on the pass filter on the surround channels.

Shelf Filter(“SH - F”) : Select “OFF” or “ON” to turn off or on the shelf filter on the surround channels.

Right Surround Channel Polarity Inversion(“PO - I”) : Select “OFF” or “ON” to turn off or on the polarity inversion.

Automatic Balancing(“BAL”) : Select “ OFF” or “ON” to turn off or on the automatic balancing

•If the Dolby Pro Logic II Music or Custom display disappears, you cannot select the parameter. In this case, select the desired surround mode again by pressing the DSP MODE button.

•In the Dolby Pro Logic II Music mode, you cannot select the 7 kHz Low Pass Filter, Shelf Filter, Right Surround Channel Polarity Inversion and Automatic Balancing.

•For your reference, the initial settings for parameters are as follows: “PANO” : “OFF”, “C-WID” : “0”, “DIMEN” : “0”, “LPF” : “OFF”, “SH-F” : “OFF”, “PO-I” : “ON”, “BAL” : “OFF”.

16