PYLE Audio PLDN70U manual Hue

1.5 The Remote Control Description

3	27	35	1
PWR		P/N

14					EQ		BAND		4
29				MU	MODE			MENU	2
									33
32
				SEL			0K		6
9									8
34			+
					SETUP				5
13
									7
31
									10
30
		1			2	3		4
									11
		-10			+10
									12
		5			6	7		8
					9	0/10
24				CLK				10+	16
	SLOW_FWD
28					ST				15
				LOC			SEARCH	APS
21									18
22				ZOOM						17
					INT		RPT	RDM
26					AUDIO	TITLE/PBC		SUBTITLE
25				A-B					19
23				PROG	OSD		LOUD	STEP	20

16.SEARCH BUTTON

17.RDM BUTTON

18.RPT BUTTON

19.SUBTITLE BUTTON

20.TITLE/PBC BUTTON

21.ANGLE/ST BUTTON

22.ZOOM BUTTON

23.AUDIO BUTTON

24.CLK BUTTON

25.A-B BUTTON

26.INT BUTTON

27.EQ BUTTON

1.TILT BUTTON

2.MENU BUTTON

3.POWER BUTTON

4.^ BUTTON

5.>> BUTTON

6.> BUTTON

7.<< BUTTON

8.v BUTTON

9.SEL BUTTON

10.PLAY/PAUSE BUTTON

11.NUMBER(0~10,+10

-10) BUTTONS

12.10+ BUTTON

13.SETUP BUTTON

14.MODE BUTTON

15.APS BUTTON

28.LOC/SLOW-FWD BUTTON

29.MUTE BUTTON

30.STOP BUTTON

31.VOLUME- BUTTON

32.< BUTTON

33.OK BUTTON

34.VOLUME+ BUTTON

35.BAND AND P/N BUTTON

36.PROG BUTTON

37.OSD BUTTON

38.LOUD BUTTON

39.STEP BUTTON

HUE

It is for adjusting the hue of the video output.

SATURATION

It is for adjusting the saturation of the video output.

SHARPNESS

It is for adjusting the sharpness of the video output.

4.24.5 SPEAKER SETUP

DOWNMIX

It is for selecting your desired sound effect when there is not central speaker and sub-woofer. There are 3 mode: LT/RT, STEREO, VSS.

LT/RT: When playing a disc with PRO LOGIC Dolby stereo effect, choose the item, so it will output audio signal with vivid theatre effect.

STEREO: If you choose the item, when outputting audio signal with 5.1 channels, it will output the left and right channels of signal ; when outputting audio signal with 2 channels, it will output the common 2 channels of stereo signal.

VSS: If you choose the item, when playing a disc recorded with 5.1 channels, the main channel speakers can output audio signal with VSS effect.

4.24.6 DIGITAL SETUP

OP MODE

It is for selecting audio output mode

LINE OUT: It can linearly compress the audio signal. So the volume level is lower. You should select the item at night.

RF REMOD: It can make the volume level higher. You should select it at daylight.

DYNAMIC RANGE

After selecting the compression mode of LINE OUT, set the item, so you can adjust the linear compression ratio. If you set it to be FULL, the Peak-to-Peak value of the audio signal is the minimum; if you set it to be OFF, the Peak-to- Peak value is the maximum.

DUAL MONO

It is for selecting a desired audio output mode for the left and right ways of signal. It is mainly for Karaoke of Ac3. There are 4 modes in all as follows:

STEREO, MONO L, MONO R, MIX MONO.

PDF created with FinePrint pdfFactory trial version http://www.pdffactory.com