QSC Audio PLX 1104 Specifications PLX 1802, PLX 2502, PLX 3102, PLX, Distortion, Smpte-Im

Specifications PLX 1802, PLX 2502, PLX 3102, PLX 3602

		PLX 1802	PLX 2502	PLX 3102	PLX 3602
OUTPUT POWER (Watts)(1)
20 - 20k Hz, 0.05% THD, 8 ohms/Ch.		320	425	550	725
1k Hz, 0.1% THD (EIA), 8 ohms/Ch.		330	450	600	775
20 - 20k Hz, 0.05% THD, 4 ohms/Ch.		525	675	900	1100
1k Hz, 0.1% THD (EIA), 4 ohms/Ch.		575	750	1000	1250
1k Hz, 0.1% THD (EIA), 2 ohms/Ch.		900	1250	1550	1800
Bridge Mono, 20 - 20k Hz, 0.1% THD, 8 ohms		1100	1400	1900	2500
Bridge Mono, 1k Hz, 0.1% THD, 8 ohms		1200	1500	2100	2600
Bridge Mono, 1k Hz, 1.0% THD, 4 ohms		1800	2500	3100	3600
DISTORTION, SMPTE-IM		<0.02%, all models
FREQUENCY RESPONSE		20 - 20k Hz, ±0.5 dB, all models
SIGNAL to NOISE, unweighted, 20 - 20k Hz		-107 dB	-106 dB	-107 dB	-107 dB
VOLTAGE GAIN		31.9 dB	34.0 dB	35.0 dB	35.9 dB
INPUT SENSITIVITY, Vrms
for rated power into 8 ohms		1.28 (+4.4 dBu)	1.15 (+3.4 dBu)	1.23 (+4.0 dBu)	1.25 (+4.2 dBu)
OUTPUT CIRCUIT TYPE		AB	AB/H	AB/H	AB/H
INPUT IMPEDANCE		10k ohms unbalanced, 20k ohms balanced
DYNAMIC HEADROOM		2 dB at 4 ohms
DAMPING FACTOR (8 ohms)		>500
AMPLIFIER PROTECTION		Short circuit, open circuit, thermal, ultrasonic and RF protection. Stable into reactive or mismatched loads
COOLING		Continuously variable speed fan; back-to-front air flow through heat sink array
CONTROLS	Front:	AC POWER switch, Gain controls (each channel) 21 detents
	Back:	Input Configuration Switch (Stereo, Parallel, Bridge), Clip Limiters (On/Off)
		Subwoofer Switch (100 Hz Low Cut/Full Range/100 Hz High Cut, each channel)
		LF Switch (33 Hz Low Cut/Full Range, 1 each channel)
LED INDICATORS		POWER (blue), SIGNAL (green x 2), -10 dB (green x 2), CLIP (red x 2), BRDG (amber), PAR (amber)
CONNECTORS	Input:	1/4-inch TRS and female XLR; 20k ohm balanced, 10k ohm unbalanced
	Output:	Speakon connectors: Ch 1, 4-wires (Ch 1 + Ch 2); Ch 2, 2-wires (Ch 2 only)
		Binding posts
LOAD PROTECTION		Turn-on/turnoff muting, DC fault blocking, Clip limiting, infrasonic filter (-3 dB at 5 Hz).
POWER REQUIREMENTS		Refer to rear panel serial number label. Configured at factory for 100, 120 or 220-240 VAC, 50- 60 Hz.
DIMENSIONS		19.0" (48.3 cm) W, 3.5" (8.9 cm) H, 13.9" (35.3 cm) D (from front mounting rails, including rear support
		ears)
WEIGHT(1)		21 pounds (9.5 kg) net;	26 pounds (11.8 kg) shipping

(1) NOTE: Due to special construction to meet EN-6100, CE models may have 5-12% (0.5 dBw) less power and 1.2 lb (0.6 kg) more weight.

U.S. patent no. 5767744 and patents pending

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

13