V . C O M F O R T A D J U S T M E N T S
V . C O M F O R T A D J U S T M E N T S
Seat Position
You can move the seat forward or rearward by changing the extrusion mounting position.
To change the position:
1. | Turn off the power to the controller. |
2. | Loosen the rear shroud fasteners and remove the rear |
| shroud. See figure 6. |
3. | Unplug the controller connector(s) from the power |
| base. |
4. | Remove the seat from the power base. |
5. | Remove both extrusions from the bottom of the seat. |
6. | Reposition the extrusions on a different set of mount- |
| ing holes. You must move both extrusions the same |
| number of holes either forward or backward. See fig- |
| ure 17. |
7. | Fasten the extrusions back onto the bottom of the seat. |
To change the armrest width:
1. Locate the two armrest knobs on each side of the armrest receiver bracket. See figure 18.
2. Loosen the knobs.
3. Slide the armrests in or out to the desired width.
4. Tighten the knobs.
Armrest Angle Adjustment
To change the armrest angle:
1. Lift the armrest straight up so that it is perpendicular to the floor. See figure 18.
2. Loosen the jam nuts.
3. Turn the adjusting screw to raise or lower the front of the armrest.
4. Tighten the jam nuts to lock the adjusting screw into place.
SETSCREW
Figure 19. Underside of Armrest
8. | Reinstall the seat. |
9. | Reconnect the controller. |
10. | Reinstall the rear shroud and tighten the fasteners. |
Controller Position
You can move the controller in toward or out away from the armrest, or change the position of the controller for either
Manual Recline Seatback Adjustment
If your power chair is equipped with a reclining seat, you can adjust the seatback angle with the seatback release lever. The lever is located on the right side of the seat base.
To adjust the recline angle:
1. Pull up on the seatback release lever.
2. Lean forward or backward to the desired position.
3. Release the lever.
Seatback Angle Adjustment
If your power chair is equipped with an adjustable seat- back, you can adjust it to four (4) different angles: 90°, 102°, 105°, or 107°.
To adjust the seatback angle:
1. Remove the adjusting screws from each seat hinge.
See figure 18.
2. Set the seatback at the desired angle.
3. Reinstall the adjusting screws to each seat hinge and tighten.
Figure 17. Seat Position Adjustment
JAM NUT |
ARMREST ANGLE |
ADJUSTING |
SCREW |
ARMREST HEIGHT |
ADJUSTMENT |
SETSCREWS |
ARMREST KNOB |
SEATBACK |
ANGLE |
ADJUSTING |
SCREW |
MANDATORY! Do not place the controller harness so that it can be pinched in the seat frame or the power base frame.
To extend the controller:
1. Flip up the armrest so it is perpendicular to the floor.
2. Loosen the setscrew on the controller bracket. See figure 19.
3. Slide the controller into or out of the armrest to the desired position.
4. Tighten the setscrew to secure the controller.
To change the controller position:
1. Turn off the power to the controller.
2. Loosen the rear shroud fasteners and remove the rear shroud.
3. Unplug the controller connector from the power base.
4. Remove any wire ties securing the controller harness to the armrest.
5. Flip up the armrest so it is perpendicular to the floor.
6. Loosen the setscrew on the controller bracket
7. Slide the controller out of the armrest.
8. Loosen the setscrew in the other armrest.
9. Place the controller in the other armrest.
10. Tighten the setscrew to secure the controller.
11. Route the controller harness to the back of the power base and plug in the controller.
12. Replace the rear shroud and tighten the fasteners.
13. Secure the controller harness to the armrest with wire ties. See figure 13.
Armrest Width Adjustment
You can change each armrest’s width independently of the other.
NOTE: Changing the armrest width may increase the overall width of your power chair.
NOTE: If your power chair is equipped with a Specialty Seat, Synergy Seat, or
Quantum 610 Series | www.pridemobility.com | 25 | 26 | www.pridemobility.com | Quantum 610 Series |
