Work Piece and Work Area Set Up

Note: The Battery Pack’s capacity will increase somewhat during the first few charging cycles.

A fully discharged Battery Pack will take about 1 hour to fully charge. Recharging the Battery Pack for more than 1 hour can damage the battery cells.

7.While charging, the Battery Pack, Charger, and Power Supply may become warm to the touch. This is normal, and does not indicate a problem.

8.The red LED will light continuously when the Battery Pack is charged. Unplug the Charger and disconnect it from the Battery Pack when finished.

9.Allow the Battery Pack to cool completely before using it.

10.Press the Battery Button to release Battery Pack from the Charger.

Safety

1. Designate a work area that is clean and well‑lit.	2.	Secure loose work pieces using a vise or clamps
The work area must not allow access by children		(not included) to prevent movement while working.
or pets to prevent distraction and injury.	3.	There must not be objects, such as utility lines,
	3.	There must not be objects, such as utility lines,

nearby that will present a hazard while working.

General Operating Instructions

1.Insert the fully charged Battery Pack (11) into the base of the Tool, making sure that it clicks into place securely. Be sure the Battery Pack is securely seated into the Drill Handle so it does not fall off during use.

2.Slide the Direction Switch (which should initially be centered in the “lock” position) to the right for forward drilling/fastening, or to the left for reversing the operation. Use the “reverse” setting only to remove screws or to release jammed drill bit.

NOTICE: Do not change direction of rotation while Chuck is rotating. Wait until Chuck has come to a complete stop before changing direction.

3.If using the Drill to insert or remove screws, position the tip in the item to insert or remove.

Wood Drilling

a.For best performance, use high speed drill bits for wood drilling and turn the torque setting to the drill icon.

b.Start wood drilling at very low speed to keep the bit from slipping. Increase speed as drill bit bites into wood.

c.When drilling through holes, place a block or wood behind the workpiece to prevent ragged edges on the back side of the hole.

Metal Drilling

a.For best performance, use high speed drill bits for metal or steel drilling and turn the torque setting to the drill icon.

Setup

4.	If drilling a hole, hold the Drill above the area to drill.		b. Start metal drilling at very low speed to keep the bit
5.	For precision depth drilling, loosen (turn		from slipping. Maintain the speed and pressure,
5.	For precision depth drilling, loosen (turn		allowing for cutting without overheating the bit.
	counterclockwise) the Driver Clamp (21)		allowing for cutting without overheating the bit.
	counterclockwise) the Driver Clamp (21)
	on the Secondary Handle (23) and move		c. When drilling large holes in metal surfaces, use a
	the Depth Gauge (23) to the desired		small drill bit at first. Then finish with a larger drill
	position. Retighten the Driver Clamp.		bit. Be sure to lubricate the bit with oil to improve
6. Press the Trigger to start the drill. The Work			the drilling action and help increase bit life.
6. Press the Trigger to start the drill. The Work
	Light will also activate once the Switch is		Masonry Drilling
	pressed and turn off once Switch is released.		a. Use carbide or specialty bits for
			a. Use carbide or specialty bits for
7. When inserting or removing a screw or bolt, use			masonry/concrete drilling.
	slight pressure at first to keep the bit in the head		b. Rock and masonry are generally drilled
	of the screw or bolt and cause the screw or bolt		b. Rock and masonry are generally drilled
	of the screw or bolt and cause the screw or bolt		in the hammer drilling mode.
	to thread into or unthread from the material.		in the hammer drilling mode.
	to thread into or unthread from the material.		c. When drilling in walls, start with regular drilling and,
8. When drilling a hole, let the Drill do the work,			c. When drilling in walls, start with regular drilling and,
8. When drilling a hole, let the Drill do the work,			once tile is pierced, continue with hammer mode.
	using only enough pressure to follow the		NOTE: In deep bore holes, occasionally pull
	drill as it cuts the hole in the material.		NOTE: In deep bore holes, occasionally pull
	drill as it cuts the hole in the material.		the drill bit out to remove dust and chips.
			the drill bit out to remove dust and chips.
9. When drilling a hard, smooth surface, use			10. When finished using the Drill, release the
	a center punch (not included) to mark the		10. When finished using the Drill, release the
	a center punch (not included) to mark the		Trigger and center the Direction Switch to lock
	desired hole. This will prevent the drill bit		Trigger and center the Direction Switch to lock
	desired hole. This will prevent the drill bit		the trigger mechanism as a safety measure.
	from slipping as the hole is started.		the trigger mechanism as a safety measure.
	from slipping as the hole is started.		11. Remove the Battery Pack.
			11. Remove the Battery Pack.
			12. Clean then store the Drill indoors
			and out of children’s reach.
	Item 68851	For technical questions, please call 1-800-444-3353.		Page 9

Operation

Maintenance

Quick Eagle Networks 68851 Work Piece and Work Area Set Up, General Operating Instructions

Models: 68851

Safety