preparing your phone
choosing your settings
Speakerphone
Thank you for purchasing your
Your phone’s display is protected by a plastic label during shipping. Peel off the label before using your phone.
installing batteries
Insert three AAA alkaline batteries (not supplied).
When 
appears or the display becomes dim, replace the batteries.
After you install your batteries, system information appears in the display, followed by E for English, F for French and S for Spanish.
1. | Repeatedly press REVIEW or to select the |
| desired display language and press DELETE to |
| store it. If you do not select a language within a few |
| seconds, the system defaults to English. |
2. | When LCD CONTRAST appears in the display, repeat |
| step 1 to select one of the six settings. |
3. | When 000 SET AREA CODE displays and the 0 |
5. Repeat Step 4 to store the minute, month and date.
To reset the language, contrast, area code and time/date settings:
1.Hold down DELETE and press . LCD CONTRAST displays.
2.Repeat Step 1 above to reset each setting.
what’s included
Stand | ||
Long Modular Cord | Short Modular Cord | |
Coiled Handset Cord | Mounting Bracket | |
3 Index Cards | User’s Guide |
|
battery notes:
•When replacing batteries, be sure to put in new batteries
within one minute of removing the old ones. If not, your time and date will be lost.
•Use only fresh batteries of the required size and recommended type.
•Do not mix batteries of different sizes or chemistries.
•Always remove old or weak batteries. Batteries can leak chemicals that can damage electronic parts.
flashes, repeatedly press REVIEW or until the first digit of your area code appears. Press DELETE to store it. Repeat for each digit of your area code.
NOTE: If you do not press a button, the system automatically sets the area code to 000.
4.Press REVIEW or to set the hour, and press DELETE to store it.
NOTE: If you do not press a key, the system automatically sets the time to 12:00 PM 1/01.
REVIEW / Scroll up or down to set the desired language, LCD contrast, area code, and time/date. Also lets you scroll through all numbers in your Caller ID memory.
Index Card
Flip open the clear cover and use the supplied index card inside to record the stored numbers.
SPEAKER – press to switch between the handset and speakerphone for convenient
CALL BACK – dial a phone number in the Caller ID record.
MEM – stores a number in an indirect memory location
mounting and connecting the phone
1.Press and pull out the stand from the base.
2.Connect the handset to your phone using the coiled handset cord, and then fit the cable in the groove as shown below.
3.Align the mounting bracket’s round tabs with the holes on the base, then slide the mounting bracket upward to snap it into place.
4.Connect one end of the short modular cord into LINE, and the other end to the wall plate jack.
5.Fit the keyhole slots over the wall plate studs. Slide the
phone downward to secure it.
6.Use a coin to turn the handset hook 180°.
Handset Hook
•Your telephone connects directly to a modular phone line jack. If your phone line jack is not a modular jack, you can update the wiring yourself using adapters and jacks from your local RadioShack store. Or, call your telephone company to update the wiring for you.
•The USOC number of the jack to be installed is RJ11C.
end a call, press SPEAKER again.
HOLD – press to put a call on hold. To resume the call, press the switchhook or lift the handset.
MUTE – press to keep the other party from hearing you. To resume the conversation, release MUTE.
REDIAL
–press to redial the last number you dialed.
OPT/P (Option/ Pause) – press to select different dialing options based on the number you are calling.
STORE – press to store numbers in memory locations. See “Memory Dialing”.
FLASH – press to answer another call if you have Call Waiting.
Use the stand to place your phone on a desk.
LINE
RINGER VOLUME HI/
LOW/OFF
Set ringer’s volume to
HI or LOW as desired.
Set to OFF for no sound.
MODE T/P/TB
See “setting the dialing mode”.
RINGER R1/R2
Mounting Bracket
HEADSET
For
Please read this user’s guide before
installing, setting up and using your new product
www.radioshack.com
Set to R1 for a high number of rings or R2 for a lower number of rings.
Coiled Handset Cord
