v2.0 (EN/FR/E)
FCC information
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to
PLEASE READ AND SAVE THIS FOR FUTURE REFERENCE
IMPORTANT SAFETY INSTRUCTIONS
user manual manual de usuario
RCD330
EN/FR/E
It is important to read this instruction prior to using your new product for the first time. Es importante leer este manual antes de usar por vez primera su equipo.
may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
operate the equipment.
This product complies with DHHS Rules 21 CFR Subchapter J. Applicable at the date of manufacture.
For your safety
The AC power plug is polarized (one blade is wider than the other) and
only fits into AC power outlets one way. If the
plug won’t go into the outlet completely, turn the plug over and try to insert it the other way. If it still won’t fit, contact a qualified electrician to change the outlet, or use a different one. Do not attempt to bypass this safety feature.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE
OF PLUG TO WIDE SLOT, FULLY INSERT.
WARNING: MAINS PLUG IS USED AS DISCONNECT DEVICE AND IT SH OU LD R EM A IN R E A DI LY OPER ABLE DURING INTENDED USE. IN ORDER TO DISCONNECT THE MAINS PLUG FROM MAINS COMPLETELY, THE MAINS PLUG SHOULD BE DISCONNECTED FROM TH E M A I N S SO C K E T O UT LE T COMPLETELY.
Some of the following information may not apply to your particular product; however, as with any electronic product, precautions should be observed during handling and use.
•Read these instructions.
•Keep these instructions.
•Heed all warnings.
•Follow all instructions.
•Do not use this apparatus near water.
•Clean only with dry cloth.
•Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
•Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
•Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.
•Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
•Only use attachments/ accessories specified by the manufacturer.
•Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When
a cart is used, use caution when
moving the cart/
apparatus combination to avoid injury from
•Unplug this apparatus during lightning storms or when unused for long periods of time.
•Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as
is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.
•IF YOUR PRODUCT OPERATES ON BATTERIES, adhere to the following precautions:
A.Any battery may leak electrolyte if mixed with a different battery type, if inserted incorrectly, or if all batteries are not replaced at the same time.
B.Any battery may leak electrolyte or explode if disposed of in fire or an attempt is made to charge a battery not intended to be recharged.
C.Discard leaky batteries immediately. Leaking batteries can cause skin burns or other personal injury. When discarding batteries, be sure to dispose
of them in the proper manner, according to provincial and local regulations.
Important Battery Precautions
•Any battery may present a risk of fire, explosion, or chemical burn if abused. Do not try to charge a battery that is not intended to be recharged, do not incinerate, and do not puncture.
•
•If your product uses more than one battery, do not mix types and make sure they are inserted correctly. Mixing types or inserting incorrectly may cause them to leak.
•Discard any leaky or deformed battery immediately. They may cause skin burns or other personal injury.
•Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
•Please help to protect the environment by recycling or disposing of batteries according to federal, state, and local regulations.
Technical information |
|
| For your records | ||||
Product: Portable CD Player with |
|
| In the event that service should be required, | ||||
|
| you may need the model number. In the space | |||||
analog Tuner |
|
|
|
| |||
|
|
|
| below, record the date and place of purchase: | |||
Brand: RCA |
|
|
|
| |||
|
|
|
| Model No. | |||
Model: RCD330 |
|
| |||||
|
| Date of Purchase | |||||
Power Supply: 120V ~ 60Hz |
|
| |||||
|
| Place of Purchase | |||||
Power Consumption: 15 Watts |
|
| |||||
|
|
|
| ||||
Unit Size (H x W x D mm): |
|
| Service information | ||||
|
| This product should be serviced only by those | |||||
139 x 310 x 247 |
|
|
|
| |||
|
|
|
| specially trained in appropriate servicing | |||
Weight: 2.1kg |
|
|
|
| |||
|
|
|
| techniques. For instructions on how to obtain | |||
CD player: Response curve (+/- 2dB): | |||||||
service, refer to the warranty included in this | |||||||
60Hz to 20 kHz |
|
| Guide. | ||||
Rating Plate: Look for it at the |
|
|
|
| |||
bottom of the set. |
|
|
|
| |||
CLASS 1 LASER PRODUCT |
|
|
|
| |||
LASER KLASSE 1 |
|
|
|
|
|
| |
APPAREIL A LASER DE CLASSE 1 |
|
|
|
| |||
LUOKAN 1 LASERLAITE |
|
|
|
| |||
KLASS 1 LASERAPP ARAT |
|
|
|
| |||
|
| Class II equipment | |||||
|
|
| |||||
|
|
|
|
|
|
| |
|
| CAUTION |
|
|
|
| |
|
|
|
|
|
| ||
|
| RISK OF ELECTRIC SHOCK |
|
|
|
| |
THE LIGHTNING |
| DO NOT OPEN |
| THE EXCLAMATION | |||
CAUTION: TO REDUCE THE |
| ||||||
FLASH AND |
| POINT WITHIN THE | |||||
ARROWHEAD WITHIN | RISK OF ELECTRIC SHOCK, |
| TRIANGLE IS A | ||||
THE TRIANGLE IS A DO NOT REMOVE COVER (OR |
| WARNING SIGN | |||||
WARNING SIGN | BACK). NO USER- |
| ALERTING YOU OF | ||||
ALERTING YOU OF | SERVICEABLE PARTS INSIDE. |
| IMPORTANT | ||||
"DANGEROUS | REFER SERVICING TO |
| INSTRUCTIONS | ||||
VOLTAGE" INSIDE THE | QUALIFIED SERVICE |
| ACCOMPANYING | ||||
PRODUCT. | PERSONNEL. |
| THE PRODUCT. |
| |||
SEE MARKING ON BOTTOM / BACK OF PRODUCT
WA R N I N G : TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
Before you begin
Useful advice
•Do not use your system immediately after transporting it from a cold place to a warm place, as condensation may cause the system to malfunction. If moisture forms inside this system, it may not operate properly. To correct the problem, turn off the power and wait about 30 minutes for moisture to evaporate.
•This system is fitted with a laser.
To avoid accidents, it is to be opened by qualified technicians only.
•Never leave the CD compartment door open as dust could cover the laser lens and/or the CD compartment door could be bumped into accidentally.
•Do not place the system near wet areas such as bathrooms and pool side. Avoid storing the system at humid places or near abnormally heated areas.
•Power is continuously supplied to the system. To disconnect power completely, unplug the power cord from the power outlet.
•Ensure minimum distance around the apparatus for sufficient ventilation. The ventilation should not be impeded by covering the ventilation openings with items,
such as newspaper, etc.
•No naked flame source, such as lighted candles, should be placed on the apparatus.
•The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
AC power
Plug the power supply cord into the AC power jack on the back of the unit, and into an AC power supply outlet that accepts the plug supplied with your unit.
Battery power
You can insert 8
•Open the battery compartment door on the bottom of the unit by pressing down on the tab and pulling out the cover.
•Before inserting the batteries, observe the polarities (that is, + and
Note that the AC line cord must be unplugged from the jack on the back of the unit to operate on batteries.
Important battery information
•Remove the batteries to avoid leakage if you do not use your system for more than one month.
•Discard leaky batteries immediately as leaking batteries may cause skin burns or other personal injuries. Dispose of batteries in the proper manner, according to provincial and local regulations.
•Any battery may leak electrolyte under the following circumstances:
-if mixed with a different battery type,
-if inserted incorrectly,
-if all batteries are not replaced at the same time,
-if disposed of in fire, or
-if an attempt is made to charge a battery not intended to be recharged
•Be sure to remove batteries when storing the set for more than 30 days. Leaky batteries can badly damage the system. Be sure to dispose of leaky, weak or dead batteries properly according
to federal, state, and local regulations. To prevent injury or
| General controls and locations | |||||||
damage, do not reverse batteries |
|
|
|
|
|
|
|
|
and do not mix battery type. |
|
|
|
|
|
|
|
|
Don’t infringe |
| 1 |
|
|
|
|
| 16 |
This product should only be used for |
|
|
|
|
|
| 15 | |
the purposes for which it is sold, that |
|
|
|
|
|
|
| |
| 2 |
|
|
|
|
|
| |
is, entertainment, violating no copyright |
|
|
|
|
|
| 14 | |
|
|
|
|
|
|
| ||
law. Any attempts to use this product |
|
|
|
|
|
|
| |
| 3 |
|
|
|
|
| 13 | |
for unintended purposes are unlawful |
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| |
and therefore not condoned by the |
| 4 |
|
|
|
|
| 12 |
manufacturer. |
|
|
|
|
|
|
|
|
|
| 5 |
|
|
|
|
| 11 |
|
| 6 | 7 | 8 | 9 | 10 |
| |
|
|
|
| |||||
| 1 | Line In Jack |
|
|
|
| 11 | CD skip |
| 2 | DBBS |
|
|
|
| 12 | Tuning control |
| 3 | Function selector |
|
|
|
| 13 | Band selector |
| 4 | Volume control |
|
|
|
| 14 | FM stereo indicator |
| 5 | CD skip |
|
|
|
| 15 | Dial pointer |
The descriptions and characteristics in | 6 | Repeat |
|
|
|
| 16 | Antenna |
7 | Stop |
|
|
|
|
|
| |
this owner’s manual are for the purpose |
|
|
|
|
|
| ||
of general reference only and not as a | 8 | CD display |
|
|
|
|
|
|
guarantee. In order to provide you with | 9 | Play / Pause |
|
|
|
|
|
|
the highest quality product, we may |
|
|
|
|
|
| ||
10 | Prog. |
|
|
|
|
|
| |
make changes or modifications without |
|
|
|
|
|
| ||
prior notice. The English version serves as the final reference on all product and operational details should any discrepancies arise in other languages.
Function of controls
1. LINE IN Jack
To connect an audio cable for external audio input.
2. DBBS
To switch on or off the bass boost.
3. Function selector
To select among the LINE IN / CD, off, radio.
4.Volume control
To adjust the volume.
5.CD skip 
To go to the previous track or search backward.
6. Repeat
To select among the repeat current track, repeat all tracks playback modes.
7. Stop
To stop the playback.
8. CD display
The CD display show your various playing modes, track numbers.
9. Play / Pause
To start and pause the playback.
10. Prog.
To enter the program mode and confirm the program settings. You can program a playlist of up to 20 tracks.
11. CD skip 
To go to the next track or search forward.
12. Tuning control
To adjust the tuning frequency.
13. Band selector
To select FM, stereo or AM band.
14. FM stereo indicator
Lights whenever FM stereo broadcast being received.
15. Dial pointer
Indicate the frequency being tuned.
16. Antena FM
Extend the antenna for better FM reception.
LINE-IN
1.Slide the function selector to
2.Connect the external player to the
3.Adjust the external player to
•Do not turn the volume of the external player too high as this may affect the sound quality.
•For other playback operations, control them on your external player.
Radio
1.Slide the function selector to RADIO position.
2.Slide the Band selector to select FM, FM stereo or AM band.
Extend the FM antenna for better FM reception.
Rotate the unit for better AM reception.
3.Rotate the tuning control to tune down or up the radio frequency. Tuned frequency can be read via the Dial pointer. When the reception is good at FM Stereo mode, FM stereo indicator will light on.
CD player
CD-R / RW This unit is compatible with 
audio CD-R/RW discs.
Notes on
•Do not affix any type of labels to either side (recordable or labeled side) of a
•Playback capability for
Selecting CD mode
Slide the function selector to
Loading disc
1.Open the CD door.
2.Place the CD on the spindle with the label side facing up and press gently to lock the disc in place.
3.Close the CD door. The total number
of tracks on the disc can be read from display.
Play and pause
1.In stop mode, press 
to begin CD playback.
2.During CD playback, press 
to pause playback. Press again to resume.
Skip and search
1.Press 
/ 
to skip to the previous or next track respectively.
2.Press and hold 
/ 
to search quickly current track backward or forward
respectively.
Stop playback
Press 
to stop playback.
Play mode
Press REPEAT to select among REPEAT mode (repeat current track / repeat all). Selection made is indicated by icons on display.
Programming
1.In stop mode, press PROG to enter program setting mode.
The program location and program icon flash on the display.
2.Press 
/ 
to select the track you want to program.
3.Press PROG again to confirm your selection and access the next program location.
4.Repeat steps 2 to 3 to program to a maximum of 20 tracks.
5.Press 
in program mode to start program playback (PROG icon lights on
the display).
•Press 
to return to stop mode. Clearing program list
Your program will be erased:
•open the CD door or
•press 
while the program playback is stopped.
Connect an audio cable (not included) to the
Notes
Important: Also keep your “Bill of Sale” as proof of purchase.
Important: Veuillez conserver votre “Facture D’achat” comme preuve d’achat.
Importante: Guarde su “Boleta de venta” como prueba de su compra.
Model no. | Product name |
| |||||||
N° du modèle | Nom du produit |
| |||||||
N° de modelo |
| Nombre del producto |
|
| |||||
Type of set |
|
|
|
|
| ||||
Type d’appareil |
|
|
|
|
| ||||
Tipo de aparato |
|
|
|
|
|
| |||
Serial no. | Invoice no. |
| |||||||
N° de série | N° de la facture |
| |||||||
N° de serie |
|
| N° de recibo |
|
| ||||
Date purchased | Dealer name |
| |||||||
Date d’achat | Nom du marchand |
| |||||||
Fecha de compra | Nombre del comerciante |
| |||||||
|
|
|
|
|
|
|
|
|
|
FOR SERVICE AND REPAIR, PLEASE VISIT
POUR ENTRETIEN ET RÉPARATION, VEUILLEZ
VISITE
PARA SERVICIO Y REPARACIÓN, POR FAVOR
VISTITAwww.1800customersupport.com/RCA
© 2008 AVC MULTIMEDIA
Limited Warranty
Información FCC
Este dispositivo cumple con la parte 15 de las reglas FCC. El funcionamiento está
ADVERTENCIA: Los cambios o modificaciones hechas a este equipo sin que la parte responsable del cumplimiento
POR FAVOR LEA Y GUARDE ESTAS INSTRUCCIONES PARA REFERENCIA FUTURA
INSTRUCCIONES DE SEGURIDD IMPORTANTES
AVC MULTIMEDIA (“AVC”) makes the following limited warranty. This limited warranty extend to the original consumer purchaser and is limited to
One Year Parts & Labor Warranty
AVC products purchased in the United States are warranted to be free from defects in materials or workmanship for a period of one year from the date of their original retail purchase. If the unit fails to conform to this warranty, we will service the product using new or refurbished parts and products, at AVC’s sole discretion.
During a period of one year from the effective warranty date, AVC will provide, when needed, service labor to repair a manufacturing defect at its designated Service Center. To obtain warranty service in the Untied States, you must first contact our Customer Support Center at www.1800customersupport.com/RCA, during the hours listed in the box below. The determination of service will be made by AVC Customer Support.
PLEASE DO NOT RETURN YOUR UNIT TO AVC WITHOUT PRIOR AUTHORIZATION. New or remanufactured replacements for defective parts or products will be used for repairs by AVC at its designated Service Center for one year from the effective warranty date. Such replacement parts or products are warranted for an additional one year from the date of repair or replacement. The Customer will be required to ship the unit to the Service Center indicated at the time Customer Support is contacted to make the necessary repairs. The customer is responsible for all transportation charges to the service facility.
Packaging and Shipping InstructionWhen you send the product to the AVC service facility you must use the original carton box and packing material or an equivalent as designated by AVC
Your Responsibility
(1)You must retain the original sale receipt to provide proof of purchase.
(2)These warranties are effective only if the product is purchased and operated in the U.S.A. or Canada.
(3)Warranties extend only to defects in material or workmanship, and do not extend to any product or parts which have been lost or discarded, or damage to product or parts caused by misuse, accident, improper operation or maintenance, or use in violation of instructions provided with the product, or to product which has been altered or modified without authori- zation of AVC, or to products or parts thereof which have had the serial number removed or changed.
Out of Warranty
In the event your product requires repair after the limited warranty period has expired, please contact our Customer Support Center at
www.1800customersupport.com/RCA
Hours:
You are responsible for any transportation, shipping or insurance relative to the return of product to our Product Returns Center.
All warranties implied by state law, including the implied warranties of merchantability and fiitness for a particular purpose, are expressly limited to the duration of the limited warranties set forth above. With the exception of any warranties implied by state law as hereby limited, the foregoing warranty is exclusive and in lieu of all other warranties, guarantees, agreements and similar obligations of manufacturer or seller with respect to the repair or replacement of any parts. In no event shall AVC be liable for consequential or incidental damages.
No person, agent, distributor, dealer or company is authorized to change, modify or extend the terms of these warranties in any manner whatsoever. The time within action must be commenced to enforce any obligation of AVC arising under the warranty or under any statute, or law of the United States or any state thereof, is hereby limited to one year from the date of purchase. This limitation does not apply to implied warranties arising under state law.
This warranty gives you specifiic legal rights and you may also have other rights, which may vary, from state to state. Some states do not allow limitation on how long an implied warranty lasts, when an action may be brought, or the exclusion or limitation of incidental or consequential damages, so the above provisions may not apply to you.
For more information on other products and services, please visit our web site at |
|
www.1800customersupport.com/RCA | Printed in China |
IMPORTER
AVC Multimedia,
Markham, Ontario, L3R 1E3
© 2008 AVC Multimedia
http: //www.1800customersupport.com/RCA
http: //www.rcaaudiovideo.com
sujeto a las siguientes dos condiciones:
(1)Este dispositivo puede que no cause interferencia nociva y (2) puede aceptar cualquier interferencia recibida, incluyendo la que pueda originarse por una operación no deseada.
Este equipo se ha probado y cumple con los límites para los dispositivos digitales de
Clase B de acuerdo con la Parte 15 de las reglas FCC. Estos límites están diseñados para brindar protección razonable contra la interferencia nociva de las instalaciones residenciales. Este equipo genera, usa
y puede emitir energía de frecuencias de radio y, si no se instala y usa de acuerdo con el manual de instrucciones del fabricante, puede causar interferencia nociva con las comunicaciones de radio. Sin embargo, no hay garantía de que
la interferencia no se presenta en una instalación particular.
Si este equipo no causa interferencia nociva a la recepción de radio o televisión, lo cual puede determinarse encendiendo o apagando el equipo, se recomienda que el usuario trate de corregir la interferencia por medio de una o varias de las siguientes medidas:
• Reoriente o reubique la antena receptora.
• Aumente la separación entre el equipo y el receptor.
• Conecte el equipo en una toma o circuito
diferente a donde está conectado el receptor.
• Consulte al proveedor o a un experto en radio/TV para obtener ayuda.
las apruebe expresamente, podría impedir que el usuario use el equipo.
Este producto cumple con el subcapítulo CFR de las reglas 21 DHHS aplicables en la fecha de fabricación.
Por su seguridad
El enchufe eléctrico AC está polarizado (una aleta es más ancha que la otra) y solamente se adapta a tomas eléctricas AC de
una vía. Si el enchufe no entra en la toma completamente, voltéelo e intente por el otro lado. Si aún no se adapta, contacte un electricista calificado para que cambie la toma o use otra. No intente pasar por alto esta norma de seguridad.
PRECAUCIÓN: PARA PREVENIR DESCARGAR ELÉCTRICAS, HAGA QUE LA ALETA ANCHA DEL ENCHUFE COINCIDA CON LA RANURA ANCHA, INSERTE COMPLETAMENTE.
ADVERTENCIA: EL ENCHUFE DE LA RED ELÉCTRICA SE USA COMO DISPOSITIVO DE DESCONEXIÓN Y DEBE PERMANECER FÁCILMENTE OPERABLE DURANTE EL USO PRETENDIDO.USA COMO DISPOSITIVO DE DESCONEXIÓN Y DEBE PERMANECER FÁCILMENTE OPERABLE DURANTE EL USO PRETENDIDO. PARA DESCONECTAR COMPLETAMENTE EL ENCHUFE DE LA RED ELÉCTRICA, DEBE DESCONECTARSE DE LA TOMA COMPLETAMENTE.
Parte de la siguiente información pude no aplicar a su producto particular; sin embargo, como con cualquier producto electrónico, deben tomarse las precauciones durante el manejo y uso.
•Lea estas instrucciones.
•Mantenga estas instrucciones.
•Ponga atención a todas las advertencias.
•Siga todas las instrucciones.
•No use este aparato cerca del agua.
•Limpie solamente con una paño seco.
•No obstruya ninguna de las aberturas de ventilación. Instale de acuerdo con las instrucciones del fabricante.
•No instale cerca de fuentes de calor como calentadores, registradores de calor, estufas u otros aparatos (incluyendo amplificadores) que produzcan calor.
•No destruya el propósito de seguridad del enchufe polarizado o tipo conexión a tierra. Un enchufe polarizado tiene dos aletas, una más ancha que la otra. Un enchufe tipo conexión a tierra tiene dos aletas y una tercera para conexión a tierra. La aleta ancha o la tercera se suministra por razones de seguridad. Si el enchufe suministrado no coincide con su toma, consulte a un electricista para que reemplace la toma obsoleta.
•Proteja el cable eléctrico para que no sea pisado, pinchado, particularmente en los enchufes, receptáculos y en el punto donde salen de los aparatos.
•Solamente use anexos/accesorios especificados por el fabricante.
•Use solamente el carro, stand, trípode, soporte o mesa especificada por el fabricante o vendida con el aparato. Cuando use el carro, tenga precaución al mover la combinación carro/ aparato para evitar lesiones al caerse.
•Desconecte este aparato durante tormentas eléctricas o cuando no lo use durante tiempo prolongado.
•Deje el mantenimiento en manos de personal calificado. El mantenimiento es necesario cuando el aparato se daña de cualquier forma, como el cable o enchufe de alimentación eléctrica, se ha derramado líquido, objetos han caído en el aparato, el aparato se ha expuesto a la lluvia o humedad, no funciona normalmente o se ha caído.
•SI SU PRODUCTO
FUNCIONA CON BATERÍAS, agregue las siguientes precauciones:
A. Cualquier batería puede derramar electrolito si se mezcla
con diferentes tipos de baterías,
si se inserta incorrectamente o si todas las baterías no se
reemplazan al mismo tiempo.
B. Cualquier batería puede derramar electrolito o explotar
si se desecha en el fuego o se intenta cargar una batería
C. Descarte inmediatamente las baterías que tengan fugas. Las baterías con fugas pueden causar quemaduras en la piel u otras lesiones personales. Cuando deseche las baterías, verifique de hacerlo de manera correcta, de acuerdo a las regulaciones locales y provinciales.
Precauciones importantes con las baterías
•Cualquier batería que se maltrate puede ocasionar incendios, explosiones o quemaduras químicas. No trate de cargar una batería
•Si su producto usa más de una batería no mezcla tipos y verifique que estén insertadas correctamente. Mezclar diferentes tipos o insertarlas incorrectamente puede hacer que goteen.
•Descarte inmediatamente cualquier batería con fugas o deforme. Las baterías con fugas pueden causar quemaduras en la piel u otras lesiones personales.
•Las baterías no deben exponerse al
calor excesivo como la luz solar, fuego o algo similar.
•Por favor ayude a conservar el medio ambiente reciclando o desechando las baterías de acuerdo a las regulaciones locales, federales o estatales.
Antes de empezar
Consejos útiles
•No use el equipo inmediatamente después de transportarlo desde un lugar frío a uno caliente puesto que la condensación puede generar malfuncionamiento. Si existe humedad en el equipo, puede malfuncionar. Para corregir el problema, interrumpa el suministro eléctrico y espere durante 30 minutos hasta que la humedad se evapore.
•Este sistema tiene láser.
•Nunca deje la puerta del compartimiento del CD abierta puesto que el polvo puede cubrir los lentes láser y/o la puerta puede golpearse accidentalmente.
•No deje el equipo cerca áreas mojadas tales como baños o piscinas. Evite almacenar el sistema en lugares húmedos o cerca de áreas anormalmente calientes.
•La energía se suministra continuamente al sistema. Para interrumpir el suministro eléctrico completamente, desconecte el cable eléctrico de la toma.
•Asegure la distancia mínima alrededor del aparato para obtener suficiente ventilación. No impida la ventilación cubriendo las aberturas de ventilación con elementos como periódicos, etc.
•No ponga llamas vivas, como velas encendidas, cerca del aparato.
•El aparato no debe exponerse a goteos ni salpicaduras como tampoco deben ponerse objetos llenos de líquidos como floreros.
Potencia de Corriente Alterna
Conecte el cable de alimentación eléctrica en el jack de potencia de corriente alterna ubicada atrás del equipo y en una toma de potencia de corriente alterna que acepte el enchufe que viene con el equipo.
Potencia de la batería
Puede insertar 8 baterías alcalinas tamaño D (no suministradas) y puede llevar su estéreo a cualquier parte.
•Abra la puerta del compartimiento de las baterías en la base del equipo, presionando la pestaña y halando la tapa.
•Antes de insertar las baterías verifique las polaridades (+ y
Note que el cable AC debe desconectarse del jack de la parte posterior del equipo para que funcionen las baterías.
Información importante sobre las baterías
•Retire las baterías para evitar que presenten fugas si no va a usar el sistema durante más de
1mes.
•Descarte inmediatamente las baterías con fugas porque pueden causar quemaduras u otras lesiones personales. Deseche las baterías de manera correcta, de acuerdo a las regulaciones locales y provinciales.
•Cualquier batería puede derramar electrolito bajo las siguientes circunstancias:
-Si se mezclan diferentes tipos de baterías,
-Si se insertan incorrectamente.
-Si todas las baterías no se reemplazan al mismo tiempo.
-Si se desechan al fuego
-Si se intenta cargar baterías no recargables
•Verifique de retirar las baterías cuando guarde el equipo durante más de 30 días. Las baterías con fugas pueden dañar el sistema. Deseche apropiadamente las baterías con fugas, débiles o agotadas, de acuerdo con las regulaciones locales, federales o estatales. Para evitar lesiones o daños, no invierta las baterías ni mezcle diferentes tipos.
No infrinja
Este producto debe usarse solamente para los propósitos planeados, es decir entretenimiento, sin violar los derechos de propiedad intelectual. Cualquier intento de usar este producto para propósitos no planeados es ilegal y no tolerado por el fabricante.
Las descripciones y características de este manual son solamente para propósitos de referencia general y no como garantía. nos reservamos
el derecho de hacer cambios sin previo aviso. La versión en inglés sirve como referencia final del producto y detalles operativos en caso de discrepancias en otros idiomas.
Es importante leer estas instrucciones antes de usar su producto por primera vez
Información técnica.
Producto: Reproductor de CD portátil con sintonizador análogo
Marca: RCA
Modelo: RCD330
Alimentación eléctrica: 120V ~ 60Hz
Consumo de energía: 15 Watts
Dimensiones del equipo (A x A x L mm): 139 x 310 x 247
Peso: 2,1kg
Reproductor de CD: Curva de respuesta (+/- 2dB): 60Hz a 20 Khz.
Placa de datos de servicio: Búsquela en la parte inferior del equipo.
CLASS 1 LASER PRODUCT
LASER KLASSE 1
APPAREIL A LASER DE CLASSE 1
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPP ARAT
ADVERTENCIA: PARA PREVENIR INCENDIOS O DESCARGAS ELÉCTRICAS, NO EXPONGA ESTE PRODUCTO A LA LLUVIA NI HUMEDAD.
Controles y ubicaciones generales
| 1 |
|
|
|
| 16 |
|
|
|
|
| 15 | |
|
|
|
|
|
| |
| 2 |
|
|
|
| 14 |
|
|
|
|
|
| |
| 3 |
|
|
|
| 13 |
| 4 |
|
|
|
| 12 |
| 5 |
|
|
|
| 11 |
| 6 | 7 | 8 | 9 | 10 | |
|
| |||||
1 | Line In Jack (Jack de |
|
|
| 11 CD skip | |
entrada) |
|
|
| 12 Tuning control (Control de | ||
2 | DBBS |
|
|
| sintonización) | |
3 | Selector de funciones |
|
|
| 13 Band selector (Selector de | |
4 | Control de volumen |
|
|
| banda) | |
5 | CD skip |
|
|
| 14 FM stereo indicator | |
6 | Repeat (repetir) |
|
|
| (Indicador FM estéreo) | |
7 | Stop (Detener) |
|
|
| 15 Dial pointer (Puntero del | |
8 | CD display (Pantalla del CD) |
|
| dial) | ||
9 | Play / Pause (Reproducir/ |
|
|
| 16 Antena | |
Pausar)
10 Prog.
Function of controls
1. Toma LINE IN
Para conectar un cable de audio para entrada de audio externa.
2. DBBS
Para encender o apagar el realce de graves.
3. Selector de funciones
Para seleccionar entre LINE IN/CD, off [apagado], radio.
4.Control de Volumen
Para ajustar el volumen.
5.Saltar CD 
Para ir a la pista anterior o buscar hacia atrás.
6. Repetir
Para seleccionar entre los modos de reproducción: repetir la pista actual, repetir todas las pistas.
7. Detener
Para detener la reproducción.
8. Pantalla del CD
La pantalla del CD muestra los diferentes modos de reproducción, números de pista.
9. Reproducción / Pausa
Para iniciar y pausar la reproducción.
10. Prog.
Para entrar al modo de programa y confirmar las configuraciones de programa. Usted puede programar una lista de reproducción de hasta 20 pistas.
11. Saltar CD 
Para ir a la pista siguiente o buscar hacia delante.
12.Control de sintonización
Para ajustar la frecuencia de sintonización.
13.Selector de banda
Para seleccionar la banda FM, estéreo o AM.
14. Indicador de FM estéreo
Se iluminará siempre que la transmisión de FM estéreo se esté recibiendo.
15. Apuntador del dial
Indica la frecuencia que se está sintonizando.
16. Antena
Extiende la antena para una mejor recepción FM.
