Reebok W-113 manual Start Watch, SET Time, Set Day, SET Date Fast Date, Indiglo NIGHT-LIGHT

W-113905-095012

THANK YOU FOR PURCHASING YOUR REEBOK® WATCH.

Please read instructions carefully to understand how to operate your Reebok® watch. Your model may not have all of the features described in this booklet.

CROWN

CROWN

START WATCH

Important: Set day and date first! Remove guard from crown and push in. For screw-in setting crown, turn COUNTERCLOCKWISE to loosen.

Note: Crown can be located at 3 o’clock or 6 o’clock position.

SET TIME

Pull crown all the way out and turn to correct time. Push crown in to restart. For screw-in setting crown, push crown in while turning CLOCK- WISE to tighten.

Watches with date: Note correct time of day (A.M. or P.M.) for proper date function.

SET DAY

Pull crown to “middle” position and turn CLOCKWISE until correct day appears. If day does not change, pull crown to “out” position and turn CLOCKWISE or COUNTERCLOCKWISE through necessary number of 24 hour periods until correct day appears.

I	IN	I	MIDDLE	I	OUT	WE
						D
		WED 14				14
WED 14				WED 14
I		I		I

SET DATE “FAST DATE”

3-Position Crown: Pull crown to “MIDDLE” position and turn CLOCK- WISE or COUNTERCLOCKWISE until correct date appears.

2-Position Crown: Pull crown to “OUT” position and turn CLOCKWISE until date changes. Repeat until correct date appears. Adjust date when month has less than 31 days. Push crown in when finished.

		NOTE: Date may need to be manually
I	14	updated at the end of each month by
14		following above procedure (otherwise
I		it will continue to 39 and then roll
		over to 00).

ROTATING TIME RING (OPTIONAL)

Position symbol (▲) at desired time to start or end activity.

Elapsed ring Tide ring

COMPASS DIRECTIONAL RING (OPTIONAL)

To get approximate compass reading, point
hour hand at sun. Adjust ring so S (South) is	S	1112		1	W
halfway between hour hand and 12. Adjust	10				2
	9				3
every hour. Make sure hour hand is always	8	7		5	4
pointed towards the sun.	E		6
					N

INDIGLO® NIGHT-LIGHT

Press button or crown to activate light. Patented (U.S. pat. 4,527,096 and 4,775,964) electroluminescent technology used in the INDIGLO® night- light illuminates entire watch face at night and in low light conditions.

BRACELET ADJUSTMENT

SLIDING CLASP BRACELET

Open locking plate. Move clasp to desired bracelet

length. Exert pressure while holding locking plate and slide clasp back and forth until it engages in grooves on underside of bracelet. Press locking

plate down until it snaps closed. Clasp can be damaged if excessive force is used.

FOLDOVER CLASP BRACELET

Find spring bar that connects bracelet to clasp. Using a pointed tool (Fig. 1), push spring bar in and gently twist bracelet to disengage. Determine wrist size, then insert spring bar in correct bottom hole (Fig. 2). Push down on spring bar, align with top hole and release to lock in place (Fig. 3).

Fig. 1 Fig. 2 Fig. 3

BRACELET LINK REMOVAL

Removing Links: Place bracelet upright and insert pointed tool in opening of link. Push pin forcefully in direction of arrow until link is detached (pins are designed to be difficult to remove). Repeat until desired number of links are removed.

Reassembly: Rejoin bracelet parts. Push pin back into link in opposite direction of arrow. Press pin down securely into bracelet until it is flush.

SOLID LINK BRACELET

Removing Links: Using a very small screw- driver, remove screws by turning counter- clockwise. Repeat until desired number of links are removed. Do not remove links adja- cent to clasp.

Reassembly: Rejoin bracelet parts and

insert screw in end of opening where it was removed. Turn screw clock- wise until tight and flush with bracelet.

WATER AND SHOCK RESISTANCE

WARNING: TO MAINTAIN WATER-RESISTANCE, DO NOT PRESS ANY BUTTONS OR PULL OUT THE CROWN UNDER WATER UNLESS YOUR WATCH IS INDICATED AS 200 METER WATER-RESISTANT.

1.Watch is water-resistant only as long as crystal, crown and case remain intact.

2.Watch is not a diver watch and should not be used for diving.

3.Screw-in setting crown and case back must be screwed into case to assure water-resistance (see Set Time). (Optional)

4.Rinse watch with fresh water after exposure to salt water.

5.Shock-resistance will be indicated on watch face or caseback. Watches are designed to pass ISO test for shock-resistance. However avoid damaging crystal/lens.

If your watch is water-resistant, meter marking or ( ) is indicated.

Water-Resistance Depth	p.s.i.a.* Water Pressure Below Surface
30m/98ft	60
50m/164ft	86
100m/328ft	160
200m/656ft	284

*pounds per square inch absolute

BATTERY

Reebok strongly recommends that a retailer or jeweler replace bat- tery. If applicable, push reset button when replacing battery. Battery type is indicated on caseback. Battery life estimates are based on certain assumptions regarding usage; battery life may vary depending on actual usage.

DO NOT DISPOSE OF BATTERY IN FIRE. DO NOT RECHARGE. KEEP LOOSE BATTERIES AWAY FROM CHILDREN.