Regency P48-1 High Elevation, GAS Line Installation, Pilot Adjustment, GAS Pipe Pressure Testing

INSTALLATION

P48-NG1 System Data

For 0 to 4500 feet altitude

Burner Inlet Orifice Sizes: #27

Max. Input Rating	51,000 Btu/h
Min. Input Rating	29,000 Btu/h
Supply Pressure	min.5.0" w.c.
Manifold Pressure
(High)	3.8"+/- 0.2"w.c.

Log Set: Ceramic fibre, 8 per set.

Vent System: Simpson Dura-Vent Direct Vent System, Regency Flex Kit

P48-LP1 System Data

Conversion Kit# 370-969

For 0 to 4500 feet altitude

Burner Inlet Orifice Sizes: #47

Max. Input Rating 48,000 Btu/h

Min. Input Rating 26,000 Btu/h

Supply Pressure min.12.0" w.c.

Manifold Pressure

(High) 11"+/- 0.2" w.c.

Log Set: Ceramic fibre, 8 per set.

Vent System: Simpson Dura-Vent Direct Vent System, Regency Flex Kit

HIGH ELEVATION

This unit is approved in Canada for altitude 0 to 4500 ft. (CAN1 2.17-M91).

GAS LINE

INSTALLATION

The gas line can be brought through either the right, the left side or the bottom of the appliance. The gas valve is situated on the bottom of the unit.

For USA installations follow local codes and/or the current National Fuel Gas Code, ANSI Z223.1.

When using copper or flex connectors use only approved fittings. Always provide a union so that gas lines can be easily disconnected for servicing. Flare nuts for copper lines and flex connectors are usually considered to meet this requirement.

Important: Always check for gas leaks with a soap and water solution or gas leak detector. Do not use open flame for leak testing.

PILOT ADJUSTMENT

Periodically check the pilot flames. Cor- rect flame pattern has three strong blue flames: 1 flowing around the thermopile, 1 around the thermocouple and 1 flowing across the burner (it does not have to be touching the burner).

Note: If you have an incorrect flame pat- tern, contact your Regency dealer for further instructions.

Incorrect flame pattern will have small, probably yellow flames, not coming into proper contact with the rear burner or thermopile or thermocouple.

The manifold pressure is controlled by a regu- lator built into the gas control, and should be checked at the pressure test point.

Note: To properly check gas pressure, both inlet and manifold pressures should be checked using the valve pressure ports on the valve.

1)Make sure the valve is in the "OFF" position.

2)Loosen the "IN" and/or "OUT" pressure tap(s), turning counterclockwise with a 1/8" wide flat screwdriver.

3)Attach manometer to "IN" and/or "OUT" pressure tap(s) using a 5/16" ID hose.

4)Light the pilot and turn the valve to "ON" position.

5)The pressure check should be carried out with the unit burning and the setting should be within the limits specified on the safety label.

6)When finished reading manometer, turn off the gas valve, disconnect the hose and tighten the screw (clockwise) with a 1/8" flat screwdriver. Note: Screw should be snug, but do not over tighten.

S.I.T. VALVE DESCRIPTION

1)Gas cock knob

2)Manual high/low adjustment

3)Pilot Adjustment

4)Thermocouple Connection - option

5)Outlet Pressure Tap

6)Inlet Pressure Tap

7)Pilot Outlet

8)Main Gas Outlet

9)Alternative TC Connection Point

The gas line connection may be made of rigid pipe, copper pipe or an approved flex connec- tor. (If you are using rigid pipe, ensure that the valve can be removed for servicing.) Since some municipalities have additional local codes it is always best to consult with your local authorities and the CAN/CGA B149 installation code.

GAS PIPE PRESSURE

TESTING

The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig. (3.45 kPa). Disconnect piping from valve at pres- sures over 1/2 psig.

Regency P48-1 Zero Clearance Direct Vent Gas Fireplace 23