Regency Wraps I2400M Installation, Before Installing Your Insert, Chimney Specifications

INSTALLATION

Regency Inserts are constructed with the high- est quality materials and assembled under strict quality control procedures that insure years of trouble free and reliable performance.

It is important that you read this manual thor- oughly and fully understand the safe instal- lation and operating procedures. The more you understand the way your Regency Insert operates, the more enjoyment you will experi- ence from knowing that your unit is operating at peak performance.

BEFORE INSTALLING

YOUR INSERT

1)Please read this entire manual before you install and use your new wood insert. Failure to follow instructions may result in property damage, bodily injury or even death. Install and use only in accordancewith manufactur- er’s installation and operating instructions.

2)Check your local building codes - Building Inspection Department. You may require a permit before installing your insert. Be aware that local codes and regulations may override some items in the manual.

WARNING: Careless installation is the major cause of safety hazard. Check all local building and safety codes before installation of unit.

3)Notify your home insurance company that you plan to install a fi replace insert or hearth heater.

4)Your fi replace insert is heavy and requires two or more people to move it safely. The insert can be badly damaged by mishan- dling.

5)If your existing fi replace damper control will become inaccessible once you have installed your Regency Insert, you should either remove or secure it in the open posi- tion.

6)Inspect your fi replace and chimney prior to installing your insert to determine that it is free from cracks, loose mortar or other signs of damage. If repairs are required, they should be completed before installing your insert. Do not remove bricks or mortar from your masonry fi replace.

7)Do not connect the insert to a chimney system servicing another appliance or an air distribution duct.

Emissions from burning wood or gas could contain chemicals known to the State of Cali- fornia to cause cancer, birth defects or other reproductive harm.

CHIMNEY

SPECIFICATIONS

Before installing, check and clean your chimney system thoroughly. If in doubt about its condi- tion, seek professional advice. Your Regency Insert is designed for installation into a masonry

fireplace that is constructed in accordance with therequirementsof"TheStandardforChimneys, Fireplaces, Vents, and Solid Fuel Burning Ap- pliance", N.F.P.A. 211, the National Building Code of Canada, or the applicable local code requirements.

The appliance, when installed, must be electri- cally grounded inaccordancewith localcodes or, in the absence of local codes, with the National Electrical Code,ANSI/NFPA70, or the Canadian Electrical code, CSA C22.1.

Regency Inserts are designed with a 6" (152mm) fl ue.

Requirements for Installing

Solid-fuel Inserts in Factory-built

Fireplaces.

1)The insert must be tested and meet the requirements of UL 1482 (U.S.) and or ULC S628 (Canada) when tested in a masonry

fireplace built per ULC S628.

2)The factory-built fi replace must be listed per UL 127 or ULC S610.

3)Clearances obtained from the masonry fi re- place tests are also relevant for installation in factory-built fi replaces.

4)Installation must include a full height listed chimney liner type HT requirements (2100 degree F.) per UL 1777 (U.S.) or ULC S635 (Canada). The liner must be securely attached to the insert fl ue collar and the chimney top.

5)Means must be provided to prevent room air passage to the chimney cavity of the

fireplace. This may be accomplished by sealingthe damperareaaround thechimney liner, or sealing the fi replace front.

6)The air fl ow within and around the fi replace shall not be altered by the installation of the insert (i.e. no louvers or cooling air or outlet ports are blocked), unless specifi cally tested as such for each factory-built fireplace manufacturer and model line. Note: using a louvered faceplate (surround) complies with this requirement.

7)Alterationofthefireplaceinanymannerisnot permitted with the following exceptions;

a.external trim pieces which do not affect the operation of the fi replace may be removed providing they can be stored on or within the fireplace for re-assembly if the insert is removed.

b.the chimney damper may be removed to install the chimney liner.

8) Circulating air chambers (i.e. in a steel

fireplace liner or metal heat circulator) shall not be blocked.

9)Means must be provided for removal of the insert to clean the chimney fl ue.

10)Inserts that project in front of the fi replace mustbesuppliedwithappropriatesupporting means.

11)Installer must mechanically attach the sup- plied label to the inside of the fi rebox of the

fireplace into which the insert is installed.

"WARNING:This fireplace has been converted for use with a wood insert only and cannot be used for burning wood or solid fuels unless all original parts have been replaced, and the

fireplace re-approved by the authority having jurisdiction."

In order for a solid-fuel insert to be certifi ed for use in factory-built fi replaces, the above information must be clearly stated in the instal- lation manual and appropriate markings. Final approval is contingent on the authority having jurisdiction.

WOOD INSERT

SPECIFICATIONS

Your fi replace opening requires the following minimum sizes:

Height: 21.5"

Width: 25"

Depth: 17"

Two faceplates are available to seal the fireplace opening:

Standard	Oversize
40" W x 30" H	48" W x 33" H

6 Regency I2400M