Manuals
/
Brands
/
Computer Equipment
/
Network Card
/
Renesas
/
Computer Equipment
/
Network Card
Renesas
M30100T3-RPD-E
- page 36
1
36
52
52
Download
52 pages, 475.43 Kb
( 36 / 52 )
Figure 4.4 Self-check procedure
Contents
Main
( 2 / 52 )
Preface
To use the product properly
Precautions for Safety
When using outside Japan
Contents
Page
Terminology
Page
Chapter 1. Precautions for Safety
WARNING IMPORTANT
CAUTION
WARNING
Warning for Installation:
Warnings for Use Environment:
Caution to Be Taken for Modifying This Product:
Cautions to Be Taken for Handling This Product:
Note on Quitting the Emulator Debugger:
Note on Final Evaluation:
Note on Malfunctions in the PC4701 System:
Notes on Downloading Firmware:
Notes on the Self-check:
Note on Making the MCU File:
Note on Clock Supply to the MCU:
Note on Version of Emulator Debugger:
Notes on Setting the Work Area When Starting Up the Emulator Debugger:
Note on Stack Area:
Note on RESET* Input:
Notes on Maskable Interrupts:
Note on Operation When Not Executing the User Program:
Notes on Address-Match Interrupt:
Note on BRK Instruction and BRK Instruction Interruption:
Notes on Software Breaks and Hardware Breaks:
Note on Accessing Address 00000h:
Notes on Watchdog Function:
Note on Stop and Wait Modes:
Note on Instructions that Access the Single-step Interrupt Vector Area:
Note on Differences between the Actual MCU and Emulator:
Page
Chapter 2. Preparation
2.1 Package Components
2.2 Other Tool Products Required for Development
2.3 Name of Each Part
(1) System Configuration
2.4 When Using the Emulator for the First Time
(1) Making the MCU File
(2) Setting the Work Area
(3) Downloading Firmware
(4) Self-check
Page
Page
Chapter 3. Setting Up
3.1 Removing and Closing the Upper Cover
When Removing and Closing the Upper Cover:
3.2 Selecting Clock Supply and Replacing Oscillator Circuit Boards
(1) Clock Supply to the MCU
Notes on Changing the Clock Supply:
(2) Using the Oscillator Circuit on the Target System
Page
(4) Replacing the Oscillator Circuit Boards
When Removing and Closing the Upper Cover:
3.4 Connecting the PC4701 and Emulation Pod
(1) Connecting the Cable to the PC4701
Note on Connecting the Cable:
Note on Securing the Screws:
3.3 Jumper Switches JP1 and JP2 on the M30100T-PRT Board
Note on Setting Switches:
Page
When Connecting the Pod Probe:
3.5 Connecting the Pod Probe
Page
Page
Chapter 4. Usage
4.1 Turning On the Power Supply
(1) Checking Connections of the Emulator System
(2) Turning On the Power
Notes on Power Supply:
Note on the Target Status POWER LED:
Note on CLOCK LED:
4.2 Downloading Firmware
(1) When It is Necessary to Download Firmware
(2) Downloading Firmware in Maintenance Mode
Note on Downloading Firmware:
4.3 Self-check
(1) Self-check Procedure
Note on Self-check:
(2) If an Error is Detected in the Self-check
Page
Page
Chapter 5. Specifications
5.1 Specifications
Page
Page
Chapter 6. Troubleshooting
( 42 / 52 )
Chapter 6. Troubleshooting
6.1 Flowchart to Remedy the Troubles
Figure 6.1 Flowchart to remedy the troubles
6.2 When the Emulator Debugger Does Not Start Up Properly
(1) When the LED Display of PC4701 is Abnormal
Table 6.1 LED's abnormal display and its checkpoints
See the PC4701 User's Manual.
See "3.4 Connecting the PC4701 and Emulation Pod" (page 27).
(2) Errors Occur When Starting Up the Emulator Debugger (When the target system is connected)
Table 6.2 Checkpoints of errors when starting up the emulator debugger (target is connected)
6.3 Operation Differs from That of Actual MCUs
(1) Cannot Reset from the Target System
Set the time for starting up (0.2 Vcc to 0.8 Vcc) 1 s or less.
(2) Data Values of RAM Area at Power-on are Different
(3) The A-D and D-A Conversion Values are Different from Expected Values
6.4 How to Request for Support
Page
Chapter 7. Maintenance and Guarantee
7.1 Maintenance
7.2 Guarantee
7.3 Repair Provisions
7.4 How to Request for Repair
Note on Transporting the Product:
