Manuals / Brands / Computer Equipment / Switch / Renesas / Computer Equipment / Switch

Renesas M37760T-RPD-E Note on Connecting the Cable:, Note on Securing the Screws:

1 64

Download 64 pages, 1.52 Mb

( 29 / 64 )

3.4 Connecting the PC4701

To connect the emulation pod to the PC4701, use the FLX120-RPD 120-pin flexible cable included

in this product package. Connect the PC4701 side connector of the FLX120-RPD to the cable

connector of the PC4701, then secure with screws.

(1) Connecting the Cable to the PC4701

Figure 3.8 shows how to connect the PC4701 and FLX120-RPD.

Figure 3.8 Connecting the PC4701 and FLX120-RPD

CAUTION

Note on Connecting the Cable:

•To connect the FLX120-RPD, be sure to hold the both sides of the PC4701 side

connector horizontally with the "UPSIDE" facing up.

•Always shut OFF power before connecting the cable. The power ON state could

destroy internal circuits.

Note on Securing the Screws:

•After connecting the emulator main unit to the FLX120-RPD, be sure to secure the

screws.

Contents

Main Page Preface To use the product properly Precautions for Safety: When using outside Japan Terminology Contents Page Page Chapter 1. Precautions for Safety WARNING IMPORTANT CAUTION WARNING Warning for Installation: Warnings for Use Environment: Caution to Be Taken for Modifying This Product: Cautions to Be Taken for Handling This Product: Page Note on Malfunctions in the PC4701 System: Notes on Downloading Firmware: Note for PC4700 System: Note on Processor Mode Register (address D8 Notes on Target System: Note on ROM Correction Function: Note on Watchdog Function: Note on Differences between Actual MCU and Emulator: Note on Software Breaks: Note on Monitor Work Area of the Emulator: Note on Watch Point: Note on Event Breaks: Note on Reading Out the MCU Internal Resources: Chapter 2. Preparation 2.2 Other Tool Products Required for Development Chapter 2. Preparation 2.1 Package Components 2.3 Name of Each Part (1) System Configuration (2) Inside of the Emulation Pod 2.4 When Using the Emulator for the First Time Page Page Chapter 3. Setting Up 3.1 Removing the Upper Cover When Removing the Upper Cover: Page Table 3.1 Switch settings of the M37760T-RPD-E 3.3 Selecting Clock Supply Note on Changing the Clock Supply: (1) Using the Oscillator Circuit on the Target System Notes on Operating with the External Clock: Page (3) Replacing the Oscillator Circuit Boards 3.4 Connecting the PC4701 (1) Connecting the Cable to the PC4701 Note on Connecting the Cable: Note on Securing the Screws: Page Notes on Connecting the Target System: 3.5 Connecting the Target System Page Page Chapter 4. Usage 4.1 Turning On the Power Supply (1) Checking the Connection of the System (2) Turning On the Power Supply Notes on Power Supply: Note on Downloading Firmware: 4.3 Starting Up Emulator Debugger - Part 1 (Setting INIT Dialog) (1) Setting MCU Tab (2) Setting CLOCK Tab Note on Setting XCIN Pin: Notes on Emulation Memory Settings: 4.4 Starting Up Emulator Debugger - Part 2 (Setting EMEM Dialog) (2) Setting MAP Tab (1) Setting Processor Mode Tab (3) Setting Debug Monitor Tab Note on Monitor Work Area: Note on Debug Bank Memory Area: Note on Watchdog Timer: 4.5 Self-check (1) Self-check Procedure Note on the Self-check: Page Page Page Chapter 5. Specifications 5.1 Specifications Table 5.1 lists the specifications of the M37760T-RPD-E. Table 5.1 M37760T-RPD-E specifications Page Page Page Page Page Page Page Page Page ( 54 / 64 ) Chapter 6. Troubleshooting When this product does not work properly, check the following. Figure 6.1 Troubleshooting when the emulator debugger starts up 6.1 Troubleshooting up to Emulator Debugger Startup (1) Errors Displayed over the Emem Dialog Box and Remedial Action 6.2 When the M37760T-RPD-E Does Not Work Properly 6.3 How to Request for Support Page Page Chapter 7. Maintenance and Guarantee 7.1 Maintenance 7.2 Guarantee 7.3 Repair Provisions 7.4 How to Request for Repair Note on Transporting the Product: