Change the Fuse
1.Remove the five screws from the rear panel of the spotlight.
2.Remove the rear panel from the body of the spot light.
3.Disconnect the Positive Wire from the battery.
4.Remove the cover from the fuse holder.
5.Remove the bad fuse and discard.
6.Replace the bad fuse with a fuse of the same amperage rating. Never replace a bad fuse with a fuse with a lower amperage rating.
GIVE US A CALL, WE'LL HELP YOU INSTALL.
PLEASE DO NOT RETURN PRODUCT TO STORE.
Visit us on the WEB
www.ultimatelaboratories.com
For Information and Technical Assistance,
Call Toll-Free in U.S.A. and Canada.
1-800-445-1797
Change the Light Bulb
1.Unscrew the bezel to access the lamp housing.
2.Disconnect the power and ground wire.
3.Pinch the ends of the retainer clip together and move it out of the way.
4.Remove the light bulb.
5.Install the new light bulb (12V DC @ 55 Watts H3 Halogen) in the housing.
6.Return the wire retainer clip to its original position.
7.Re-attach the power and ground wires.
8.Return the lamp housing to its original position.
9.Screw the bezel onto the spotlight’s body
Negative Ground Wire
Wire Retainer Clip
Pinch the ends together
Light Bulb
Positive Wire
Remove Clip Through Slot
Reflector Housing
Troubleshooting
•If the spotlight does not turn on, check the battery condition by pressing the “Battery Status” button on the charging panel. If no LEDs light, the battery is dead or the fuse is blown. If the fuse is blown follow the instruction on the previ- ous page to replace the fuse. Fully recharge the battery, then press the “Battery Status” button again. If no LEDs light, the battery must be replaced.
•If the battery checks “Good”, but the lamp still does not light, replace the bulb.
•If the “Red” charging indicator does not light when the AC wall charger is plugged in, the wall charger may be defective.
•Call Ultimate Laboratories Technical Support at 1-800-445-1797 for assistance.
Limited Warranty
Ultimate Illumination Laboratories® products are designed and manufactured to provide a high level of trouble-free performance. Ultimate Illumination Laboratories® products are warranted by Roadmaster (USA) Corp. to the original purchaser, that its products are free from defects in material and workmanship for 30 days from the date of original purchase. As part of our commitment to product excellence, Roadmaster (USA) Corp. and/or its affiliates routinely improves the designs, materials or production methods of its existing products. Because it is impractical to publicize all changes in every product, we reserve the right to make such changes without notice.
DISCLAIMER: Purchaser understands that the manufacturer and retailer of this product have no control over how this product is used by the end user. Accordingly, the purchaser/end user assumes sole and complete responsibility for proper and/or legal installation and use of this product, including any and all liability resulting from such use and/or misuse of the product. Manufacturer disclaims all warranties expressed or implied, including but not limited to merchan- tibility and fitness for a particular purpose. Manufacturer disclaims all warranties expressed or implied, including but not limitedto merchantibility and fitness for a particular purpose.
CONDITIONS OF WARRANTY.
If during the 30 day warranty period your new product is found to be defective, Ultimate Illumination Laboratories® will repair such defect, or replace the product, without charge for parts or labor subject to the following conditions:
1.All repairs must be performed by Roadmaster (USA) Corp. and/or its affiliates in Eatontown, New Jersey.
2.The equipment must not have been altered or been damaged through negligence, accident, or improper operation.
3.The replacement of parts are exempted from this warranty when replacement is necessary due to normal wear and tear.
4.All warranty claims must be accompanied by a copy of the sales receipt or bill of sale.
5.Repair or replacement parts supplied by Roadmaster (USA) Corp. under this warranty are protected only for the unexpired portion of the original warranty.
6.In the case of car audio, this warranty does not extend to the elimination of car static or motor noise; correction of antenna problems; costs incurred for the removal or reinstallation of the product; damage to tapes, speakers, acces- sories or car electrical systems.
7.Roadmaster (USA) Corp. will not be responsible for any charge incurred for installation.
OWNER’S RESPONSIBILITIES:
Roadmaster (USA) Corp. will make every effort to provide warranty service within a reasonable period of time.
SHOULD YOU HAVE ANY QUESTIONS ABOUT SERVICE RECEIVED, OR IF YOU WOULD LIKE ASSISTANCE IN OB- TAINING SERVICE, PLEASE CALL TOLL FREE 1-800-445-1797, 8:30am - 4:30pm EST.
In order to provide you with the proper warranty service, we request that you adhere to the following procedure:
1.Include a copy of your sales receipt or bill of sale with your unit when it is returned for warranty service.
2.If it is necessary to return your product for service, please return it securely packed, preferably in the original shipping carton, and freight and insurance prepaid to the following address: Ultimate Illumination Laboratories, Service Depart- ment, 41 James Way, Eatontown, New Jersey 07724.
3.Please include a detailed explanation of the problem you are having.
4.If your product is found by Roadmaster (USA) Corp. to have a defect in material or workmanship, within the warranty period, it will be repaired or replaced at no charge and returned to you prepaid. Where permitted by law Roadmaster (USA) Corp. liability shall be limited to that set forth in this warranty. This warranty shall be the exclusive remedy of the purchaser.
Roadmaster (USA) Corp. makes no other warranty of any kind, expressed or implied; and all implied warranties, are hereby disclaimed by Roadmaster (USA) Corp. and excluded from this warranty, Roadmaster (USA) Corp. and/or its affiliates, the manufacturer, distributor and seller shall not be liable for any injury, loss or damage, incidental or conse- quential, arising out of the use or intended use of the product.
©2008 Intellectual Solutions Inc., All Rights Reserved, All designs, logos and images are the exclusive property of Intellectual Solutions Inc. and/or its affiliates. U.S. and Foreign Patents Pending. 091608 Printed in China 00000
