INSTALLATION

WIRING THE SYSTEM

!

CAUTION: If you do not feel comfortable with wiring your new unit, please see your

 

local Authorized Rockford Fosgate Dealer for installation.

!

CAUTION: Before installation, disconnect the battery negative (-) terminal to prevent

damage to the unit, fire and/or possible injury.

CAUTION: Avoid running power wires near the low level input cables, antenna, power

!leads, sensitive equipment or harnesses. The power wires carry substantial current and could induce noise into the audio system.

1.Plan the wire routing. Keep RCA cables close together but isolated from the amplifier's power cables and any high power auto accessories, especially electric motors. This is done to prevent coupling the noise from radiated electrical fields into the audio signal. When feeding the wires through the firewall or any metal barrier, protect them with plastic or rubber grommets to prevent short circuits. Leave the wires long at this point to adjust for a precise fit at a later time.

2.Prepare the RED wire (power cable) for attachment to the amplifier by stripping 1/2" of insulation from the end of the wire. Insert the bared wire into the B+ terminal and tighten the set screw to secure the cable in place.

NOTE: The B+ cable MUST be fused 18" or less from the vehicle's battery. Install the fuseholder under the hood and prepare the cable ends as stated above. Connections should be water tight.

3.Trim the RED wire (power cable) within 18" of the battery and strip1/2"of insulation from the end of the wire. Cut the wire loop that is attached to the fuseholder in half and splice the fuse into the power line using appropriate inline connectors. Use the section of cable that was trimmed earlier and connect it to the other end of the fuseholder.

4.Strip 1/2" from the battery end of the power cable and crimp a large ring terminal to the cable. Use the ring terminal to connect to the battery positive terminal. DO NOT install the fuse at this time.

5.Prepare the BLACK wire (Ground cable) for attachment to the amplifier by stripping 1/2" of insulation from the end of the wire. Insert the bared wire into the GND terminal and tighten the set screw to secure the cable in place. Prepare the chassis ground by scraping any paint from the metal surface and thoroughly clean the area of all dirt and grease. Strip the other end of the wire and attach a ring connector. Fasten the cable to the chassis using a non-anodized screw and a star washer.

Use one of the two following connection methods;

RCA Cable Connection

1.Prepare the REM turn-on wire for connection to the amplifier by stripping 1/2" of insulation from the wire end. Insert the bared wire into the REM terminal and tighten the set screw to secure the cable into place. Connect the other end of the REM wire to a switched 12 volt positive source.

The switched voltage is usually taken from the source unit's accessory lead. If the source unit does not have this output available, the recommended solution is to wire a mechanical switch in line with a 12 volt source to activate the amplifier.

6

Page 5 Page 7
Page 6
Image 6
Rockford Fosgate RFT3081A, RFT3061A, RFT3101A manual Wiring the System, RCA Cable Connection
Page 5 Page 7

RFT3081A, RFT3101A, RFT3061A specifications

Rockford Fosgate, a renowned name in the audio industry, has consistently delivered high-quality sound systems that cater to the needs of music enthusiasts and professionals alike. Among its latest offerings are the RFT3061A, RFT3101A, and RFT3081A models, which stand out due to their advanced features, cutting-edge technologies, and superior sound performance.

The Rockford Fosgate RFT3061A is a 6.5-inch component speaker system designed for superior sound clarity and powerful performance. One of its main features is the Flex Fit basket, which allows for an easy installation in a variety of vehicle types. The RFT3061A is equipped with a high-quality polypropylene cone and a butyl rubber surround, delivering exceptional responsiveness and durability. The integrated 1-inch silk dome tweeters provide rich highs and are adjustable, allowing users to tailor the sound to their preferences.

The RFT3101A takes performance to the next level with its 10-inch subwoofer. This model integrates the innovative VAST (Vertical Attach Surround Technique) technology, which increases the cone area for improved bass output without compromising space. The RFT3101A boasts a power handling capability of up to 300 watts RMS, ensuring that it can produce deep, impactful lows with clarity. Its dual voice coil configuration allows for versatile wiring options, giving users the flexibility to customize their audio setup.

For those seeking a balanced audio experience, the RFT3081A is a remarkable 8-inch full-range speaker. This model features a weather-resistant design, making it ideal for outdoor settings or marine applications. The RFT3081A incorporates a high-temperature voice coil for increased power handling and efficiency, coupled with a stamped steel frame for robust support. Users will appreciate the enhanced soundstage created by the cone's design, which promotes uniform sound distribution across frequencies.

All three models reflect Rockford Fosgate's commitment to quality, with rigorous testing ensuring reliability and performance even in the harshest environments. The combination of premium materials, innovative technologies, and user-friendly features makes the RFT3061A, RFT3101A, and RFT3081A standout choices for any audio enthusiast looking to enhance their sound experience. Whether you're upgrading your vehicle's audio system or looking for powerful solutions for outdoor events, these models deliver exceptional performance that embodies the Rockford Fosgate legacy.
Top Page Image Contents