69
Parameter list
Parameter list
KEYBOARD parametersPEDAL parameters
TRANSMIT SWITCH
PROGRAM
CHANGE
OFF, ON If this is “ON,” a program change message will be trans-
mitted when you press a NUMBER button or BANK
button.
1.
Hold down the CANCEL button and
press the TAP button
2.
Press the PRESET button and then press
the BANK C button
3.
Press a NUMBER button (5–8)
5:
PROGRAM CHANGE
6:
BANK SELECT
7:
EDIT DATA
8:
ACTIVE SENSING
Lit:
ON,
Dark:
OFF
4.
Press the CANCEL button
BANK SELECT OFF, ON If this is “ON,” a MIDI bank select message will be
transmitted when you press a GROUP button (PRESET
or USER).
EDIT DATA OFF, ON If this is “ON,” changes you make to the patch settings
will be transmitted as system exclusive messages.
ACTIVE SENSING OFF, ON Turns transmission/reception of active sensing mes-
sages on/off.
Parameter Value Explanation Panel operation
OCTAVE SHIFT -3– +3 Shifts the keyboard pitch up or down in steps of one oc-
tave.
Press the OCT UP/DOWN buttons (p. 18)
TRANSPOSE
VALUE
-5– +6 Shifts the keyboard pitch up or down in semitone steps. Hold down the CANCEL button and press
the OCT UP/DOWN buttons
LOCAL SWITCH OFF, ON Determines whether the sound generator section is dis-
connected (OFF) from the controller section (keyboard,
pitch bend/modulation lever, knobs, buttons, D Beam
controller, pedal, and so on); or not disconnected (ON).
* Normally this is left “ON,” but if you wish to use the
SH-201’s keyboard and controllers to control only
external sound modules, set it to “OFF.”
1.
Hold down the CANCEL button and
press the TAP button
2.
Press the PRESET button and then press
the BANK D button
3.
Press the NUMBER 2 button
Lit:
ON,
Dark:
OFF
4.
Press the CANCEL button
REMOTE
KEYBOARD
OFF, ON Set this parameter “ON” when you want to use an ex-
ternal MIDI keyboard instead of the SH-201’s keyboard.
In this case, the MIDI transmit channel of the exter-
nal MIDI keyboard can be set to any channel.
* Normally you will leave this parameter “OFF.”
1.
Hold down the CANCEL button and
press the TAP button
2.
Press the PRESET button and then press
the BANK D button
3.
Press the NUMBER 3 button
Lit:
ON,
Dark:
OFF
4.
Press the CANCEL button
Parameter Value Explanation Panel operation
PEDAL POLARITY STANDARD,
REVERSE
Selects the polarity of the pedal.
On some pedals, the electrical signal output by
the pedal when it is pressed or released is the
opposite of other pedals. If your pedal has an
effect opposite of what you expect, set this pa-
rameter to “REVERSE.”
* If you are using a Roland pedal (that has no po-
larity switch), set this parameter to “STAN-
DARD.”
Hold down the CANCEL button and press
a GROUP button (PRESET or USER)
PRESET:
STANDARD
USER:
REVERSE
PEDAL ASSIGN HOLD,
MODULATION,
VOLUME,
BALANCE,
PAN,
EXPRESSION,
START/STOP,
ARP-SW
Selects the function controlled by a pedal connect-
ed to the PEDAL jack.
HOLD:
Sustain the sound while you continue
holding down the pedal (p. 21).
MODULATION:
Apply modulation when you
press the pedal.
VOLUME:
Control the volume.
BALANCE:
Vary the volume balance between
the UPPER tone and LOWER tone.
PAN:
Move the left/right position (when out-
putting in stereo).
EXPRESSION:
Add expression to your perfor-
mance (p. 21).
START/STOP:
Press the pedal to start/stop re-
cording or playback on the recorder.
ARP-SW:
Press the pedal to turn the arpeggia-
tor on/off.
Hold down the CANCEL button and press
a NUMBER button (1–8)
1:
HOLD
2:
MODULATION
3:
VOLUME
4:
BALANCE
5:
PAN
6:
EXPRESSION
7:
START/STOP
8:
ARP-SW
Parameter Value Explanation Panel operation
SH-201_r_e.book 69 ページ ２００６年４月２７日 木曜日 午前１１時２８分