Rotel RA-05 owner manual Troubleshooting, Specifications, Volt Trigger Outlet

12 Volt Trigger Outlet \

Some audio components can be turned on automatically when they receive a 12V turn on “signal”. The two12V Trigger Outputs of the RA-05 provide the required signal. Connect compatible components to the RA-05 with a conventional 3.5mm miniplug cable. When the RA-05 is in Standby mode, the trigger signal is interupted, so the components controlled by it are turned off.

Protection Indicator 3

The RA-05 has both thermal and over-current protection circuitry that protects the amplifier against damage in the event of extreme or faulty operating conditions. The protection circuits are independent of the audio signal and have no impact on sonic performance. Instead, the protection circuits monitor the temperature of the output devices and shut down the amplifier if temperatures exceed safe limits.

9

Troubleshooting

Most difficulties in audio systems are the result of incorrect connections, or improper control settings. If you encounter problems, isolate the area of the difficulty, check the control settings, determine the cause of the fault and make the necessary changes. If you are unable to get sound from the RA-05 refer to the suggestions for the following conditions:

Power Indicator Is Not Lit

The Power Indicator should be lit whenever the RA-05 is plugged into the wall power outlet and the Power Switch is pushed in. If it does not light, test the power outlet with another electrical device, such as a lamp. Be sure the power outlet being used is not controlled by a switch that has been turned off.

English

Fuse Replacement

If another electrical device works when plugged into the power outlet, but the Power Indicator of the RA-05 does not light when plugged into the same outlet and the Power Switch is pushed in, it indicates that the internal power fuse may have blown. If you believe this has happened, contact your authorized Rotel dealer to get the fuse replaced.

No Sound

Check the signal source to see if it is function- ing properly. Make sure the cables from the signal source to the RA-05 inputs are connected properly. Be sure the Listening Selector is set to the proper input. Check the wiring between the RA-05 and the speakers.

Most likely, you will never see this protection circuitry in action. However, should a faulty condition arise, the amplifier will stop playing and the LED indicator on the front panel will light up.

If this happens, turn the amplifier off. Let it cool down for several minutes, and attempt to identify and correct the problem that caused the protection circuitry to engage. When you turn the amplifier back on, the protection circuit will automatically reset and the indicator LED should go out.

In most cases, the protection circuitry activates because of a fault condition such as shorted speaker wires, or inadequate ventilation lead- ing to an overheating condition. In very rare cases, highly reactive or extremely low imped- ance speaker loads could cause the protection circuit to engage.

If the protection circuitry triggers repeatedly and you are unable to isolate and correct the faulty condition, contact your authorized Rotel dealer for assistance in troubleshooting.

Specifications

Continuous Power Output	40 watts/ch
(20-20 kHz, < 0.03%, 8 ohms)
Total Harmonic Distortion (20Hz-20kHz)	< 0.03% at rated power, 1/2 power or 1 watt
Intermodulation Distortion (60 Hz : 7 kHz, 4:1)	< 0.03% at rated power, 1/2 power or 1 watt
Frequency Response
Phono Input	20Hz-15kHz, ±0.3dB
Line Level Inputs	10Hz-40kHz, ±1dB
Damping Factor (20-20,000 Hz, 8 ohms)	180
Input Sensitivity / Impedance
Phono Input	2.5mV / 47 kOhms
Line Level Inputs	150 mV / 24 kOhms
Input Overload
Phono Input	180mV
Line Level Inputs	5V
Premp Output / Impedance	1V / 470 Ohms
Tone Controls - Bass / Treble	±6 dB at 100Hz / 10kHz
Signal to Noise Ratio (IHF “A” weighted)
Phono Input	80 dB
Line Level Inputs	100 dB
Power Requirements
USA Version	120 Volts, 60 Hz
European Version	230 Volts, 50 Hz
Power Consumption	220 Watts
Dimensions (W x H x D)	437 x 72 x 342 mm
	17 1/8 x 27/8 x 131/2”
Panel Height	60 mm / 23/8”
Weight (net)	5.9 kg, 13 lbs.

All specifications are accurate at the time of printing.

Rotel reserves the right to make improvements without notice.