Rover Mowers Limited | Chip `N Shred | SAFETY INSTRUCTIONS |
General Electrical Safety Rules
1.Avoid dangerous environments such as damp locations.
2.Do not abuse the power cord. Never pull a machine by the cord or pull the cord to disconnect it from the outlet socket. Keep the cord away from excessive heat, oil, and sharp edges.
3.Disconnect the machine when not in use, before servicing and when changing attachments.
4.Avoid accidental starting. Be sure to switch off before plugging the cord into a power outlet.
5.To prevent electrical shock, use the machine only with an extension cord suitable for outdoor use as recommended by the extension cord manufacturer; the use of suitable extension cords is extremely important for the operator's personal safety.
6.Never use an indoor type of extension cord: these cords are designed for use with lamps and small appliances and are inadequate for
7.Make sure the extension cord is in good condition. A cord with cracked or broken insulation is hazardous, particularly in the presence of moisture or combustible material. It is also important that the cord connectors be of rugged construction, in good condition, and securely attached to the outer jacket.
8.If the extension cord is damaged in any manner while operating the machine, immediately switch off the power supply and remove the extension cord from the power outlet.
9.If the supply cord is damaged it must be replaced by a CMG Service Agent or similarly qualified person in order to avoid a hazard.
Electrical Supply Capacity and Fuses
1.Use only an electric circuit having adequate capacity.
2.Blowing a fuse or tripping a circuit breaker is a warning that you are overloading your machine or have too many devices in use on that circuit, or both. Determine the cause and correct it. Do not install a higher capacity fuse.
|
|
| 1. SPECIFICATIONS |
Rover Model No: | 9885 (Electric) | 9858 (Petrol) | 9859 (Petrol) |
|
|
|
|
Engine Model No: | A09189 | 91202 | 135202 |
Power rating | 2.42 Kw (High Torque) | 2.6 Kw | 3.75 Kw |
Fuel Capacity |
| 1.9 litres | 2.85 litres |
Oil Capacity |
| 600ml | 600ml |
Oil Grade |
| SAE 30 | SAE 30 |
Spark Plug |
| RJ 19 LM | RJ 19 LM |
Spark Plug Gap |
| 0.7 - 0.8mm | 0.7 - 0.8mm |
Voltage | 240 volts |
|
|
Current FL. | 10 amps |
|
|
Frequency | 50Hz |
|
|
Phase | Single |
|
|
No. Flails | 12 | 12 | 12 |
No. chipper blades | 1 | 1 | 1 |
|
|
| _ |
Chipper opening | 71 x 71 mm | 71 x 71 mm | 71 x 71 mm |
Weight | 56 | 51 | 56 |
|
|
|
|
2.1 Loose Parts Kit |
|
Feed hopper half LH | 1 |
Feed hopper half RH | 1 |
Hopper baffle | 1 |
Hopper handle | 1 |
Hopper washers | 4 |
Chipper tube assembly | 1 |
Manual | 1 |
Bar screen assembly | 1 |
Screws- 10 x 3/4" pan p/head | 12 |
Bolts- 1/4" x | 4 |
Nyloc nuts- 1/4" unc | 4 |
Screws- 3/16" x 5/8" mush.head | 4 |
| 2. SETTING UP |
Nyloc nuts- 3/16" unc | 4 |
Washer- 3/16" x 1/2" x 20g.flat | 4 |
Washer- 3/16" x 3/4" x 16g.flat | 4 |
Nyloc nuts- 5/16" unc | 7 |
Setscrew- 5/16" x 1" unc. hex | 7 |
Washers- 5/16" x 5/8" x 18g. flat | 7 |
When disassembling the timber packing, discard the four nuts and retain the bolts and washers for the handle assembly. The four nyloc nuts found in the loose parts list are to be used on the handle bolts.
