14. MAINTENANCE
Cleaning the Body of the laminaor
1.To clean the machine body, dampen a cloth with water only and gently wipe the machine clean.
Removing Adhesive Build Up
1.Remove the film from the laminator.
2.Use a damp (water only) cloth and a rubber gum eraser to remove the adhesive on the Teflon (metal) and silicone rollers.
Note: Rub firmly but do not scrub the rollers vigorously as this may scratch the surface.Do not use sharp metal objects, steel wool, or abrasives, as these may also damage the rollers.
Lubrication
1.Drive chain and sprockets should be lubricated with either a light coat of gear lube or heavy grease (lithium grease) after 6 months or 1000 hours of operation, whichever comes first.
15.TROUBLESHOOTING
Problem | Cause | Solution | |
|
|
| |
|
| a. Plug the power cord into appropriate | |
| a. Power plug is not plugged in. | outlet. | |
Machine will not turn | b. Power switch is in “0” (Off) position. | b. Put the power switch to the “I” (On) | |
on: | c. Tripped circuit breaker. | position. | |
| d. Blown main power fuse. | c. Reset the circuit breaker. | |
|
| d. Replace the fuse. | |
|
|
| |
There is power, but the | a. Emergency switch (es) is (are) | a. Disengage the emergency switch (es). | |
engaged. | |||
rollers are not turning | b. Properly install the paper guide so that | ||
b. Paper guide is not installed correctly. | |||
after the “RUN” button | the micro switch is activated. | ||
| |||
is pressed: | c. Blown motor fuse. | c. Replace the motor fuse. | |
|
| ||
|
|
| |
The unit is not heating | a. Did not raise the temperature. | a. Raise the temperature. | |
up: | |||
|
| ||
|
|
| |
Curled lamination: | a. Upward curl. | a. Loosen the top roll film tension. | |
b. Downward curl. | b. Loosen the bottom roll film tension. | ||
| |||
|
|
|
RSC
16. SPECIFICATIONS
| 60Hz | 100W |
|
|
| Not applicable | None |
| Not applicable |
|
|
|
| No |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
| 120V |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| linkChainto mai motor |
|
|
| (mm) |
|
|
|
|
| 220~240V200,50/60Hz |
| 1400mm/ 55" | mic25~250/ 1~10mil | /5m/min16.4ft/min |
|
| gearedDC |
| settings9 | Roller2 | gripAuto(2",3") | Yes |
| Yes | 15mm/ 0.6" | Yes | Yes | Yes |
| (&'%33850(mm).5" | (&'% | |||
|
|
|
|
|
| 1710 (&'%9001960164kg5".67/ 3577".5" (&'%(&'%595lbs270kg(&'%/ | |||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| .5" 47 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ( &' % 361lbs 5" . 21 650 | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1210 |
| (&'% | ||
AC 100, | 1650W,800W |
|
|
| 10min | RollerHot |
| 50 | #!"!"$ |
| Yes |
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| F |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ! " |
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| 22/ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| l |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Description | Power supply | Power consumption | Max laminating width | Film thickness | Max laminating speed | Ready time | Heating method | Driving motor | Max Temperature contro | Speed control | Transport type Film core size | Cross cutter | Hot lamination | Cold lamination | Mounting thickness | Take up system | Reverse | Remote control | Foot pedal | Unit dimensions | (w x d x h) | Unit weight Carton dimensions (w x d x h) Gross Weight | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
17 | 18 |
