Rotate the knob on the string head to wind the string. If using a curved shaft trimmer, knob should be rotated counterclockwise. If using a straight shaft trimmer or brushcutter, knob should be rotated clockwise. Wind the string until approximately 8 in. remains protruding from each side of the string head.
NOTE: During string trimmer operation, the string will advance auto- matically as needed. Do not bump the string head on the ground in an attempt to advance string.
TROUBLESHOOTING
If line does not advance automatically, it may be twisted or stuck inside the string head. Stop the trimmer, remove the line, and re- install.
If the line still does not advance properly, check to ensure the spool and lifter assembly are installed properly and that you are using the correct spring for your unit.
If you have difficulty loading line, try inserting it through the other eyelet or trimming the end of the line to remove bent or frayed edges.
Use black bolt |
for curved shaft |
trimmers. |
Use silver bolt |
for straight |
shaft trimmers |
and brush- |
cutters. |
using the adaptors
Along with the Universal Auto Feed Reel Easy String Head and
Diagrams above represent order of parts installation, however, all parts may not be needed for your trimmer. Consult the Adaptor Chart and use only the Adaptor Configuration specified for your trimmer.
Craftsman® is a registered trademark of Sears, Roebuck and Co. Yard Machine®,
TECHTRONIC INDUSTRIES
NORTH AMERICA, INC.
1428 Pearman Dairy Road
Anderson, SC 29625
Phone
www.ryobitools.com
987000-625
Universal | Washer | Spring | Thread Spacer | Tightening | Nut | Bolt |
Adaptor | (Used | (Black | Adaptor | Tool | (6 Sizes) | (Black |
| With Nuts | & Silver) |
|
|
| & Silver) |
| A, C & D Only) |
|
|
|
|
|
Find your trimmer model in the Adaptor Chart below, then use the adaptor configuration listed to install the Auto Feed String Head Assembly on your trimmer. For units that require the universal adaptor, insert the specified nut into the universal adaptor as shown.
NOTE: This string head is not recommended for use on Echo straight shaft,
Refer to the diagrams at right to see how the pieces fit together.
WARNING:
Failure to use the correct adaptor, nut, spring, and bolt combination for your trimmer could cause the string head to detach from your trimmer and result in serious personal injury and/
or property damage.
Adaptor Chart
Other models and brands not listed may fit with the use of the universal adaptor, a nut, the silver spring and the silver bolt. For these units, test the adaptor with each nut to find one that tightens securely. Test the string head to ensure that the string will contact the cutter on the grass shield before operating. If the string head does not fit with any of the adaptors or nuts supplied, contact Customer Service at
Model | Type | Adaptor Configuration |
|
|
|
Ryobi | Curved Shaft | Direct Fit + Black Spring + Black Bolt |
|
|
|
Ryobi | Straight Shaft | Direct Fit + Silver Spring + Silver Bolt |
|
|
|
Homelite | Curved Shaft | Direct Fit + Black Spring + Black Bolt |
|
|
|
Homelite | Straight Shaft | Direct Fit + Silver Spring + Silver Bolt |
|
|
|
MTD* | Curved Shaft | Thread Adaptor (tightened with Tightening Tool) + Spacer |
|
| + Black Spring + Black Bolt |
|
|
|
MTD* | Straight Shaft | Thread Adaptor (tightened with Tightening Tool) + Spacer |
|
| + Black Spring + Black Bolt |
|
|
|
*MTD brands include Bolens, Cub Cadet,
Poulan** | Curved Shaft | Washer + Universal Adaptor + Nut A + Silver Spring + Silver Bolt |
|
|
|
Poulan** | Straight Shaft | Universal Adaptor + Nut E + Silver Spring + Silver Bolt |
|
|
|
** Poulan brands include Poulan, Poulan Pro, Weed Eater, and select Craftsman | ||
|
|
|
Craftsman | Straight Shaft | Universal Adaptor + Nut F + Silver Spring + Silver Bolt |
|
|
|
Craftsman | Curved Shaft | Washer + Universal Adaptor + Nut A + Silver Spring + Silver Bolt |
|
|
|
Echo | Curved Shaft | Universal Adaptor + Nut B + Silver Spring + Silver Bolt |
|
|
|
